manualshive.com logo in svg

Pepperl+Fuchs HD2-GTR-4PA, Manual, Page: 9 / 84

Share
Download
Pepperl+Fuchs HD2-GTR-4PA Manual Download Page 9

P R O F I B U S   P

O W E R

  H

U B

  S

E G M E N T

  C

O U P L E R

Safety

Subject to reasonable modifications due to technical advances.

Copyright Fuchs, Printed in Germany

Fuchs Group • Tel.: G49 621 776-0 • USA +1 330 4253555 • Sin65 67799091 • Internet http://www.pepperl-fuchs.com

9

Dat

e

 of

 I

ssue 

24.

3.

11

Connection or disconnection of energized non-intrinsically-safe circuits
is only permitted in the absence of a hazardous area.

Instructions for Zone 22

 

The devices may only be installed and operated in zone 22 if mounted
in an enclosure for which an EC-type-examination certificate acc. 94/9/
EG for at least category 3D exists.

1.8.2

Mounting instructions for HD2-GT* modules

The modules are intended for mounting on an appropriate Fieldbus Po-
wer Hub Gateway motherboard.

1.8.3

Shield/Grounding

Take care about good earthing practice and specific earthing require-
ments of your installation  (see chapter “Shield/Grounding” on page 23).

Observe IEC 60079-14 for requirements of potential equalization.

1.9

Housing

The device must be mounted at least in protection category IP 54 in ac-
cordance with IEC 60529/EN 60529.

If additional housings are needed for installation in hazardous areas, the
following points must be considered / evaluated:

•

Degree of protection as per IEC/EN 60529

•

Light resistance as per IEC/EN 60079-0

•

Impact strength as per IEC/EN 60079-0

•

Chemical resistance as per IEC/EN 60079-0

•

Heat resistance as per IEC/EN 60079-0

•

Electrostatics as per IEC/EN 60079-0

To ensure the IP degree of protection:

•

All seals must be undamaged and have been correctly fitted.

•

All screws of the housing / housing cover must have been tigh-
tened with the appropriate torque.

•

Only cable of the appropriate size must be used in the cable
glands.

•

All cable glands must have been tightened with the appropriate
torque.

•

All empty cable glands must have been sealed with sealing
plugs.

1.10

Repair and Maintenance

The devices may not be repaired, changed or manipulated. If there is a
defect, the product must always be replaced with an original part.

Summary of Contents for HD2-GTR-4PA





















































































Reviews:

No comments