Pentax 18981 - Ist D Igital Camera SLR Operating Manual Download Page 148

Page: 148 / 164

150

Ap
pe
nd
ix

• Do not use a spray type blower.
• Do not clean the CCD when the exposure mode is set to

(Bulb) mode.

• Always cap the lens mount area to prevent dirt and dust from accumulating

on the CCD when no lens is on the camera.

• It is recommended that you use the AC adaptor when cleaning the CCD.
• When the battery level is low, “Not enough battery remaining to clean sensor”

is displayed on the LCD monitor.

• If you are not using the AC adapter, please use batteries with ample capacity

remaining. A warning beep will sound if the battery capacity becomes low
during cleaning. Please interrupt your cleaning operation immediately.

• Do not put the tip of the blower inside the lens mount area. If the power is

turned off, this could cause damage to the shutter or the CCD sensor.

Summary of Contents for 18981 - Ist D Igital Camera SLR





































































































































































Search results

Summary of Contents for 18981 - Ist D Igital Camera SLR

Reviews:

Related manuals for 18981 - Ist D Igital Camera SLR

Brands by name

Popular brands

Pentax 18981 - Ist D Igital Camera SLR, Operating Manual

Search results

Summary of Contents for 18981 - Ist D Igital Camera SLR

Reviews:

Related manuals for 18981 - Ist D Igital Camera SLR

Brands by name

Popular brands