Pentair Fleck 4600-MECH Installer Manual Download

Page: 67 / 88

Installer Manual Fleck 4600 - MECH - Troubleshooting

Ref. MKT-IM-027 / B - 01.06.2018

67 / 88

10.

Troubleshooting

Problem

Cause

Solution

Softener fails to
regenerate
automatically

Interrupted power or switched off
power source.

Restore the controller and connect to
constant power source.

Disconnected/faulty meter cable.

Check connections in the power head
and on the meter cover. Change the
cable.

Defective power cord.

Replace cord.

Defective motor.

Change motor.

Defective controller.

Change controller.

Blocked meter.

Clean or change meter.

Bad programming.

Program correctly.

Softener delivers
hard water

By-pass valve is open.

Close by-pass valve.

No salt in the brine tank.

Add salt in the brine tank and keep salt
level above water level.

Plugged injector and/or filter.

Clean or replace injector and/or filter.

Insufficient water flowing into brine
tank.

Check brine tank filling time and clean
flow regulator.

Hot water tank hardness.

Repeated flushing of the hot water
tank.

Leak at the distributor hose.

Ensure the distributor tube has no
cracks. Check the o-ring.

Internal valve leak.

Change seals & spacers and/or piston
assembly.

Blocked meter.

Clean or change meter.

Disconnected/faulty meter cable.

Check connections in the power head
and on the meter cover. Change the
cable.

Bad programming.

Program correctly.

Excessive salt
consumption

Improper brine refill setting.

Check use of salt and setting of brine
refill.

Too much water in the brine tank.

See problem below: Too much water in
the brine tank.

Bad programming.

Program correctly.

Summary of Contents for Fleck 4600-MECH

























































































Search results

Summary of Contents for Fleck 4600-MECH

Reviews:

Related manuals for Fleck 4600-MECH

Brands by name

Popular brands

Pentair Fleck 4600-MECH, Installer Manual

Search results

Summary of Contents for Fleck 4600-MECH

Reviews:

Related manuals for Fleck 4600-MECH

Brands by name

Popular brands