Pentair Evolio 255 10 Installer Manual Download Page 71

Page: 71 / 90

Installer manual Evolio 255 740-760 - Maintenance

Ref. MKT-IM-037 / D - 25.10.2021

71 / 90

8.5.7.4

Motor and camshaft replacement

1. Remove the softener and valve covers, see Covers removal (softener and valve) [

→

Page 62].

2. Disconnect the motor

(4)

from the optical sensor

(1)

3. Remove the white locking pin

(3)

securing the motor

(4)

4. Turn the motor

(4)

counter clockwise and slide it out of its position.

5. Slide the camshaft

(2)

backwards until it is released from its mounting boss, then lift it up.

6. Change motor

(4)

and/or camshaft

(2)

CAUTION

Do not push the flappers down with the camshaft, otherwise damages may occur.

7. Put the camshaft (2) back in its backplate location leaving the camshaft slightly angled on the

left of the flappers when looking at the valve from the front.

8. Push on the flappers from left to right with the camshaft (2), rotate it manually until the 2

arrows on the top plate and camshaft (5) are aligned.

9. Slide the camshaft (2) forwards until it fit completely in its mounting boss.

10. Slide the motor (4) in its position and turn it clockwise.

11. Remount the white locking pin (3) securing the motor (4).

12. Connect the motor (4) to the optical sensor (1).

13. Remount the softener and valve covers, see Covers removal (softener and valve) [

→

Page 62]

Summary of Contents for Evolio 255 10



























































































Search results

Summary of Contents for Evolio 255 10

Reviews:

Related manuals for Evolio 255 10

Brands by name

Popular brands

Pentair Evolio 255 10, Installer Manual

Search results

Summary of Contents for Evolio 255 10

Reviews:

Related manuals for Evolio 255 10

Brands by name

Popular brands