background image

Warranty Rev. 12/13

STANDARD LIMITED WARRANTY

Pentair Hydromatic

®

 warrants its products against defects in material and workmanship for a period of 12 months 

from  the  date  of  shipment  from  Pentair  Hydromatic  or  18  months  from  the  manufacturing  date,  whichever  

occurs first – provided that such products are used in compliance with the requirements of the Pentair Hydromatic  

catalog  and  technical  manuals  for  use  in  pumping  raw  sewage,  municipal  wastewater  or  similar,  abrasive-free,  

noncorrosive liquids. 

During the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair 

or replace to the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic 

reserves the right to change or improve its products or any portions thereof without being obligated to provide such 

a change or improvement for prior sold and/or shipped units.

Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up 

through  the  Pentair  Hydromatic  website:  http://forms.pentairliterature.com/startupform/startupform.asp?type=h.  

Warranty is effective only if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing 

devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover 

only the lower seal and labor thereof for all dual seal pumps. Under no circumstance will Pentair Hydromatic be 

responsible  for  the  cost  of  field  labor,  travel  expenses,  rented  equipment,  removal/reinstallation  costs  or  freight 

expenses to and from the factory or an authorized Pentair Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or 

maintain the unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident 

or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units that 

are not installed in accordance with applicable local codes, ordinances and good trade practices; (e) if the unit is 

moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and 

manufactured;  (g)  to  any  unit  that  has  been  repaired  or  altered  by  anyone  other  than  Pentair  Hydromatic  or  an 

authorized Pentair Hydromatic service provider; (h) to any unit that has been repaired using non factory specified/

OEM parts.

Warranty  Exclusions:  PENTAIR  HYDROMATIC  MAKES  NO  EXPRESS  OR  IMPLIED  WARRANTIES  THAT  EXTEND 

BEYOND  THE  DESCRIPTION  ON  THE  FACE  HEREOF.  PENTAIR  HYDROMATIC  SPECIFICALLY  DISCLAIMS  THE 

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.

Liability  Limitation:  IN  NO  EVENT  SHALL  PENTAIR  HYDROMATIC  BE  LIABLE  OR  RESPONSIBLE  FOR  

CONSEQUENTIAL,  INCIDENTAL  OR  SPECIAL  DAMAGES  RESULTING  FROM  OR  RELATED  IN  ANY  MANNER  TO  

ANY  PENTAIR  HYDROMATIC  PRODUCT  OR  PARTS  THEREOF.  PERSONAL  INJURY  AND/OR  PROPERTY  DAMAGE  

MAY  RESULT  FROM  IMPROPER  INSTALLATION.  PENTAIR  HYDROMATIC  DISCLAIMS  ALL  LIABILITY,  INCLUDING 

LIABILITY  UNDER  THIS  WARRANTY,  FOR  IMPROPER  INSTALLATION.  PENTAIR  HYDROMATIC  RECOMMENDS 

INSTALLATION BY PROFESSIONALS.

Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or 

consequential damages and therefore such limitations may not apply to you. No warranties or representations at any 

time made by any representatives of Pentair Hydromatic shall vary or expand the provision hereof.

1101 MYERS PARKWAY 

490 PINEBUSH ROAD, UNIT 4

ASHLAND, OHIO 44805 

CAMBRIDGE, ONTARIO, CANADA N1T 0A5

PH: 855-274-8948 

PH: 800-387-4386   ORDERS FAX: 888-606-5484

WWW.HYDROMATIC.COM

Warranty Rev. 09/18

1101 Myers Parkway 

Ashland, Ohio 44805

USA

Ph: 855.274.8948

490 Pinebush Road 

Unit 4 

Cambridge, Ontario N1T 0A5

Canada

Ph: 800.387.4386

Orders Fax: 888.606.5484

www.Hydromatic.com

Summary of Contents for S3R













Reviews: