background image

13

  

E-03-577 (01-23-20)

WARRANTY

Pentair Hydromatic® warrants its products against defects in material and workmanship for a period of 12 months from installation 
date or 18 months from manufacturing date, whichever occurs first – provided that such products are used in compliance with the 
requirements of the Pentair Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or 
similar, abrasive-free, noncorrosive liquids.

During the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair or replace to 
the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic reserves the right to change or 
improve its products or any portions thereof without being obligated to provide such a change or im-provement for prior sold and/or 
shipped units.

Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up through the 
Pentair Hydromatic website: 

http://forms.pentairliterature.com/startupform/startupform.asp? type=h

. Warranty is effective only 

if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and 
monitored or this warranty will be void. Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. 
Under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/
reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.

This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or main-tain the 
unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident or negli-gence; (c) to normal 
maintenance services and parts used in connection with such service; (d) to units that are not installed in accordance with applicable 
local codes, ordinances and good trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for 
purposes other than for what it is designed and manufactured; (g) to any unit that has been repaired or altered by anyone other than 
Pentair Hydromatic or an authorized Pentair Hydromatic service provid-er; (h) to any unit that has been repaired using non factory 
specified/OEM parts.

Warranty Exclusions: PENTAIR HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES THAT EXTEND BEYOND THE 
DESCRIPTION ON THE FACE HEREOF. PENTAIR HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.

Liability Limitation: IN NO EVENT SHALL PENTAIR HYDROMATIC BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL, IN-CIDENTAL 
OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO ANY PENTAIR HYDROMATIC PROD-UCT OR PARTS 
THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY RESULT FROM IMPROPER INSTALLATION. PENTAIR HYDROMATIC 
DISCLAIMS ALL

LIABILITY, INCLUDING LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. PENTAIR HYDROMATIC RECOM-MENDS 
INSTALLATION BY PROFESSIONALS.

Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or consequential 
damages and therefore such limitations may not apply to you. No warranties or representations at any time made by any 
representatives of Pentair Hydromatic shall vary or expand the provision hereof.

Summary of Contents for C4S(X)P Series

















Reviews: