manualshive.com logo in svg

PenBits PK017, Assembly Instructions Manual, Page: 66 / 66

Share
Download
PenBits PK017 Assembly Instructions Manual Download Page 66

Offer  up  each  bogie  into  the  aperture  at  its  end  of  the  loco. Engage  the  free  end  of
the  cardan  shaft  into  the  loco's flywheel  drive  socket  and  line  up  the  Pivot  Frame

fixing hole with the hole in the chassis block. Fit the bogie retaining screw - some thread
locker is probably a good idea.

Place the locomotive on some track and give it a test run under power.

Run the locomotive in, gently at first. If the loco does not run freely or begins to bind
up  at  any  point, pay  particular  attention  to  lubrication  of  the  axle  bearings.  You  can

feel  for  any  binding  by  rotating the  wheel  rims  with  the  fingers  -  there  is  enough  slack  in
the  drive  train  gears  that  you  should  be  able to  distinguish  between  a  binding  and  a  free
wheelset.

Finally, replace the body of the locomotive.

All  being  well,  thats  it!  -  the  modifications  are  complete  and  you  have  a(nother)
sprung diesel loco.

IMPORTANT  NOTE:  If  you  need  to  remove  the  body  subsequently,  please  DO  NOT  at  any
stage  attempt  to  pull  the  chassis from  the  loco  by  pulling  on  the  bogies,  as  this  may
damage the spring mountings.

Bachmann 'Peak': Final Assembly

66/65

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Summary of Contents for PK017



































































Reviews:

No comments