manualshive.com logo in svg

PenBits PK017, Assembly Instructions Manual, Page: 54 / 66

Share
Download
PenBits PK017 Assembly Instructions Manual Download Page 54

Taking  the  axles  one  at  a  time,  slide  on  to
each  axle  the  Bachmann  axle  bearings

followed by the kit's Bearing Carriers. Note that
the  ears  at  the  tops  of  the  bearing  carriers
face outwards towards the ends of the axle.

Take  the  centre  and  outer  axles  and  clip
them  in  to  the  Drive  Unit  using  the

Bachmann bearings.

Check  for  sufficient  differential  twisting
movement between the two axles: view the

drive  unit  end-on,  and the  axle  ends  should  be
free  to  move  up  and  down  about  ±0.5mm  with
respect  to  one  another  when  the  axles  are
twisted 

in 

opposite 

senses 

about 

the

longitudinal axis of the unit.

Orientate  the  Subframe  and  the  Bachmann
drive  unit.  The  drive  unit  goes  towards  the

outer (i.e. pony truck) end of the bogie, driving
the centre and outer axles, with the socket for
the  cardan  shaft  facing  the  inner  end  of  the
bogie. Fit  the  drive  unit  into  the  Subframe,
engaging the four bearing carriers into the slots
in the subframe.

Holding  the  Drive  Unit  with  one  hand  and
the  Subframe  with  the  other,  check  that

the  Drive  Unit can  move  freely  up  and  down
relative  to  the  Subframe  with  the  carriers
sliding  in  their  slots.  At  rest the  tops  of  the
carriers  will  be  level  with  the  tops  of  the
subframes.  The  suspension  is  designed  to
deflec t ±0.5mm,  so  the  free  movement  needs
to  be  maintained  both  when  the  base  of  the
drive  unit  is  parallel with  the  base  of  the
subframe,  and  when  one  axle  is  raised  up  to
1mm  with  respect  to  the  other.  If  there  is  any  binding  when  the  units  are  parallel,  check
the  movement  of  individual  carriers  in  their slots  and  correct  as  necessary.  If  there  is
binding  when  one  axle  is  raised,  open  out  the  Bachmann  axle bearings  just  a  fraction
more, up to a maximum of 2.3mm.

That  concludes  the  test.  Unclip  the  axles  from  the  Drive  Unit  and put  them  to  one
side, ensuring that each axle bearing is kept with its respective Bearing Carrier.

Bachmann 'Peak': Wheelsets

54/65

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Summary of Contents for PK017



































































Reviews:

No comments