pellenc HELION 3 Operating Instructions Manual Download Page 32

Page: 32 / 36

ELECTRIC HEDGE TRIMMER HELION 3

54_161520-B

11. COMPLIANCE STATEMENTS

11.1. STATEMENT

OF COMPLIANCE: HELION 3

MANUFACTURER/ENTITY AUTHORISED TO COM-

PILE THE TECHNICAL FILE

PELLENC

ADDRESS

Quartier Notre-Dame - 84120 Pertuis (France)

We hereby declare that the machine referred to below as:

GENERIC DENOMINATION

ELECTRIC HEDGE TRIMMER

FUNCTION

ELECTRIC BATTERY POWERED HEDGE TRIMMER INTENDED FOR

TRIMMING BUSHES / HEDGES

COMMERCIAL NAME

HELION 3

TYPE

HELION 3

MODEL

HELION 3

SERIAL NO.

54U00001 - 54U49999 54V00001 - 54V49999 54W00001 - 54W49999

Complies with the relevant provisions of the machinery directive (2006/42/EC).

Complies with the provisions of the following European directives:

• 2014/30/EU EMC Directive; 2011/65/EU ROHS Directive; 1907/2006 REACH Regulation; 2012/19/EU WEEE

Directive.

The following harmonized European standards were used:

• EN 62841-1: 2016 ; EN 62841-4-2: 2019 ; EN 60529 :1991 + A2: 2013 + AC: 2019; EN 55014-1: 2017; EN

55014-2: 2015

Sound power level:

• Measured sound power level L

WAm

: 92 dB(A)

• Guaranteed sound power level L

WAg

: 93 dB(A)

The measurements of the measured sound power level and the guaranteed sound power level were carried out

by the notified body SGS-CSTC Shanghai, 588 Wast Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, Chi-

na following a procedure in accordance with Directive 2000/14/EC Annex V. The certificates have the numbers :

SHES210901802471.

SIGNED IN PERTUIS, DATED 18/05/2021
JEAN-MARC GIALIS
CHIEF EXECUTIVE OFFICER

Summary of Contents for HELION 3





































Search results

Summary of Contents for HELION 3

Reviews:

Related manuals for HELION 3

Brands by name

Popular brands

pellenc HELION 3, Operating Instructions Manual

Search results

Summary of Contents for HELION 3

Reviews:

Related manuals for HELION 3

Brands by name

Popular brands