Peg-Perego RANGER 538, Use And Care Manual

Page: 9 / 40

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• Before starting, check that there are no people or
objects obstructing the vehicle’s path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
PROBLEMS?
RULES FOR SAFE DRIVING
PEG PEREGO
offers an after-sales assistance service,
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the “Assistance Centres”
booklet included in the packaging.
The item’s serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
CONSUMER
SATISFACTION QUESTIONNAIRE
which you can find on
the internet at: www.pegperego.com , making
any observations or suggestions you might have.
ASSISTANCE SERVICE
ASSEMBLY INSTRUCTIONS
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
32 • Unplug vehicle wiring terminal A from battery
terminal B, by pressing terminals on side and
pulling apart.
33 • Plug the battery charger terminal to a wall outlet
following the instructions enclosed. Connect the
plug B to the battery charger plug C.
34 • Once the charge is completed unplug recharger
from wall outlet. Unplug recharger cord terminal
C from battery terminal B.
35 • Insert plug B into plug A, pressing all the way
until it clicks into place. Always remember to
close the hood and tighten the screw.
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Position the double seat. To secure the double
seat, rotate the red lock 180° using a
screwdriver.
2 • Using a screwdriver and the spanner (supplied),
secure the double seat in the front (under the
rear mudquards).
3 • Position the roll-bar. Tighten the four screws to
fix the seat.
4 • Insert the end of the safety belt in the slot
situated centrally in the bottom of the seat, as
shown in the figure.
5 • Attach the two lights above the roll-bar.
6 • Assemble the two parts of the steering wheel.
7 • Place the spring inside the central cavity in the
steering wheel.
8 • Remove the protective tab on the sound module
(part. A) and place it in the cavity, ensuring that
the side with the tab is facing upwards.
9 • Rest the horn cover on top of the sound
module. Ensure that the steering wheel is
positioned as shown in the picture.
10 • Clip on the frame section. Ensure that it is
positioned correctly, as shown in the picture.
11 • Insert the steering wheel on the steering wheel
column.
12 • Align steering wheel column holes with steering
wheel: nut fits into haxagon hole, bolt into round
hole.
13 • Loosen the safety screw that holds the hood
shut.
14 • To install the windscreen, slide the trigger in the
direction shown to release the hood. Move the
hood forward.
15 • Insert the windscreen.
16 • Tighten the four screws to fix it.
17 • Press the rearview mirrors in place. The rearview
mirrors can be swivelled in different positions.
18 • Position the rear lights, pushing them till they
click.
19 • Attach the top part of the front bumper to the
body of the vehicle.
20 • Fix the bumper with the two screws provided.
21 • Open the hood.
22 • Plug the battery into the vehicle’s electrical
system.
ATTENTION: Always fasten the hood when
finished. The vehicle is ready for use.
VEHICLE CHARACTERISTICS AND USE
23 • A: horn button. Pressing both sides, the horn
honks.
B: electric accelerator/brake pedal. Lifting your
foot off the pedal, the brake applies automatically.
C: gearshift lever.
D: Safety belt catches.
24 • To unfasten the safety belts:1 push towards the
middle and simultaneously press the button; 2
detach the buckle.
25 • GEAR SHIFT LEVERS: 1: first speed. 2: second
speed. R: reverse.
26 • SECOND SPEED: When the red lock-out is
positioned as shown in the figure, the vehicle will
run in first speed and reverse only. The turtle on
the lock-out is in the up position. To use the
second gear, follow the instructions: loose the
screw on the red lock-out.
27 • Remove the red lock-out.
28 • Rotate it 180° until the hare is in the up
position. Insert the lock-out into the hole
provided.
29 • Tighten the screw. By pushing the gearshift lever
backward, the vehicle moves into second gear.
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
30 • Open the hood. Remove the battery clamp.
31 • Replace the battery. Reposition the battery
holder and close the hood.
CHARGING THE BATTERY