Peavey XR-AT, Operating Manual

Page: 16 / 20

Specifications
INPUT SENSITIVITY:
Mic In to full power at the power amp. Master Volume Nom.
Full Nominal
-40 dBu -22 dBu
Line In to full power at the power amp. Master Volume Nom.
Full Nominal
-10 dBu +8 dBu
CHANNEL EQ:
Shelving EQ
Low EQ 80 Hz ±15 dB
Mid-Morph
Low 250 Hz ±15 dB
High 4 kHz ±15 dB
High EQ 12 kHz ±15 dB
CLIP LED:
Clip LEDs come on 3 dB before clipping.
FREQUENCY RESPONSE:
All controls nominal (detent)
Mic to Main 20 Hz – 20 kHz +0, -1 dB
Line to Main 20 Hz – 30 kHz +0, -1 dB
Mic to Amp 50 Hz – 20 kHz +0, -3 dB
Line to Amp 40 Hz – 20 kHz +0, -3 dB
PHANTOM POWER:
+48 VOLTS
NOISE:
Main = Main line output, 22 – 22 kHz filter
Amp 1 = Amplifier output, loaded at 4 Ohms, through AP
AUX-0025 switching amplifier filter
All controls full down.
Main
<-
95 dBu
Amp 1
<-
60 dBu
Master Volume nominal
Main
<-
88 dBu
Amp 1
<-
55 dBu
THD:
All controls nominal
<
0.01% @ main line output, -30 dBu in mic input Channel 1
<
0.5% @ amp 1 @ 400 Watts into 4 Ohms
All controls nominal
<
0.005% @ main line output, +4 dBu in line input Channel 1
<
0.5% @ amp 1 @ 400 Watts into 4 Ohms
MASTER EQ:
80Hz ±12 dB
250Hz ±12 dB
500Hz ±12 dB
1kHz ±12 dB
2kHz ±12 dB
4kHz ±12 dB
10kHz ±12 dB
METER ARRAY:
LIMIT
-6 dB
-12 dB
-18 dB
-24 dB
-30 dB
AMP LIMITER:
Limits amplifier power just before clipping. The limiter holds the amp
power without clipping and can be driven up to 18 dB past maximum
output.
AMPLIFIER OUTPUT POWER:
120VAC
Both channels loaded at 8 ohms: 280 Watts RMS per ch
Both channels loaded at 4 ohms: 500 Watts RMS per ch
POWER REQUIREMENTS:
Domestic: 120VAC 50/60Hz 200 Watts Nominal
Export: 230VAC 50/60Hz 200 Watts
Nominal
SIZE:
Dimensions: H x W x D
9.5" x 19" x 9.5"
24.13cm x 48.26cm x 24.13cm
WEIGHT: 16 lbs.
7.25 kgs
Features and specifications subject to change without notice.
Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian, MS • 39305
(601) 483-5365 • FAX (601) 486-1278 • www.peavey.com • 31700107 • ©2015
Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005