Rear Panel
POWER SWITCH
This is the main power switch.
FUSE
This is the main safety fuse for the
AC line voltage. Only replace with
a fuse of the exact type and rating.
If the fuse continues to open, do
not over fuse. Take the unit to an
authorized Peavey service center.
NOTE: If the main AC voltage is
changed, the fuse must also be
changed to one of the appropriate
rating for the voltage you are
switching to.
AC POWER INLET
This is the receptacle for an
IEC line cord, which provides
AC power to the unit. Connect
the line cord to this connector to
provide power to the unit. Damage
to the equipment may result if
improper line voltage is used. (See
line voltage marking on unit.)
Never break off the ground pin
on any equipment. It is provided
for your safety. If the outlet used
does not have a ground pin, a
suitable grounding adapter should
be used and the third wire should
be grounded properly. To prevent
risk of shock or fire hazard, always
make sure that the amplifier and all
associated equipment is properly
grounded.
NOTE: FOR UK ONLY
As the colors of the wires
in the mains lead of this
apparatus may not correspond
directly with the colored markings
identifying the terminals in your
plug, proceed as follows: (1) The
green and yellow wire must be
connected to the terminal which is
marked with the letter E, or by the
earth symbol, or is colored green, or
green and yellow. (2) The blue wire
must be connected to the terminal
which is marked with the letter N, or
the color black. (3) The brown wire
must be connected to the terminal
which is marked with the letter L, or
the color red.
VOLTAGE SELECTOR
SWITCH
This switch allows the user
to select between 115VAC / 60Hz
or 230VAC / 50Hz. To change the
voltage selector, you must first
unscrew and remove the plastic
cover that protects the switch.
After changing the voltage, please
replace the plastic cover to ensure
the voltage level is not inadvertently
altered.
NOTE: The fuse MUST be changed to
the appropriate value to match the
voltage you have selected. Please
see the note on the back of the
mixer for the correct value.
POWER AMP 1 SPEAKER OUTPUTS
(MAIN MIX)
Dual two-conductor 1/4" –
Speakon
®
combination jacks that
can be connected to your speakers.
Each amplifier has a minimum load
impedance of 4 ohms. This means
you can connect either one 4-ohm,
one 8-ohm or two 8-ohm speakers
to each amplifier. Do not operate
below rated minimum impedance.
For maximum power transfer and to
prevent damage to your amplifier, be
sure to use speaker cables and not
instrument cables to connect to the
speakers. We recommend the use of
18-gauge or larger speaker wire.
POWER AMP 2 SPEAKER OUTPUTS
(MAIN MIX or MONITOR MIX)
Dual two-conductor 1/4" – Speakon
combination jacks that can be
connected to your speakers. Each
amplifier has a minimum load
impedance of 4 ohms. This means
you can connect either one 4-ohm,
one 8-ohm or two 8-ohm speakers
to each amplifier. Do not operate
below rated minimum impedance.
For maximum power transfer and to
prevent damage to your amplifier,
be sure to use speaker cables and
not instrument cables to connect to
the speakers. We recommend the
use of 18-gauge or larger speaker
wire. The signal going to Power Amp
2 is determined by the position of
the Power Amp 2 Assign switch (24).
In the “MAIN” position, the main
mix is fed to power amp 1 and power
amp 2. In the “MON” position, the
main mix is fed to power amp 1 and the
monitor mix is fed to power amp 2.
FOOTSWITCH EFFECTS DEFEAT (TS)
This 1/4" jack accepts a momentary,
dual - footswitch (Peavey Part#
03014070) designed to defeat the
effects on all channels or toggle the
Auto-Tune
®
on/off. Pressing switch
1 of the footswitch will toggle the
effects on and off. The condition
will be indicated by the EFX Defeat
button on the front panel. When
defeated, the button will be red.
When the effects are active, the
button will be dark. Pressing switch
2 will toggle the Auto-Tune on /
off (globally). The status will be
indicated by the three Auto-Tune
on/off switches (5) at the top of
the first 3 channels. If Auto-Tune is
active, the switch will be amber. If it
is inactive, the switch will be dark.
44
45
46
47
49
50
48
POWER
ON
A/C
MAIN
50/60 Hz 200 WATTS
Consumo de energia 200 Wh
PO
WER AMP 1
PO
WER AMP 2
SPEAKER OUTPUTS
MINIMUM LOAD
4 OHMS PER AMPLIFIER
CLASS 2 WIRING
MAIN/MONITOR
(WITH FRONT PANEL MONITOR SWITCH ACTIVE THESE
OUTPUTS RECEIVE SIGNAL FROM MONITOR SECTION)
FOOTSWITCH
8PIN/MIDI
AUTO-TUNE
PRESETS
EFFECTS\
AUTO-TUNE
DEFEAT
TIP- EFX DEFEAT
RING- AT DEFEAT
FUSE
115V
230V
FOR 220-240V OPERATION, FUSE
MUST BE CHANGED TO T5AH/250V
FOR 115V OPERATION, FUSE
MUST BE CHANGED TO T10AH/250V
220-240V
T5AH/250V
115V
T10AH/250V
HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE.
PAR UN FUSIBLE DE MEME TYPE ET DE 250 VOLTS.
CAUTION
AVIS:
BE PLACED ON THIS APPARATUS. TO PREVENT THE RISK OF FIRE
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
WARNING:
THIS APPARATUS SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE
AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT
TEL QU’UN VASE, NE DOIT ETRE POSE SUR CELUI-CI. REMPLACER
DANS LE BUT DE REDUIRE LES RISQUES D’INCENDIE OU DE
DECHARGE ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE
A LA PLUIE OU A L’HUMIDITE ET AUCUN OBJET REMPLI DE LIQUIDE,
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
MADE IN CHINA
DESIGNED AND ENGINEERED IN U.S.A.
A PRODUCT OF PEAVEY ELECTRONICS CORP.
CAN-ICES-3B/NMB-3B
FCC ID: I4S-XR-
AT
IC: 3642B-XR-
AT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CONNECTORS COMPATIBLE
WITH TWIST-LOCK
CONNECTORS AND 1/4”
SPEAKER CABLE
1-
NEG
PINOUT
TWIST-LOCK
1/4”
SLV
44
45
46
47
48
49
50
51
