Pearl VX10RSPRO Owner'S/Operator'S Manual Download Page 19

Page: 19 / 24

– 19 –

1 Cutting head weldment - Black PLEASE CALL

2 1.5HP Electric motor - KWW105 PLEASE CALL

3 Rail carriage assembly - Black PLEASE CALL

4 M10 x 1.5 x 230 Slot bolt PLEASE CALL

5 Helical Spring PLEASE CALL

6 Power switch housing complete PLEASE CALL

7 Cutting head position bracket - Black PLEASE CALL

8 M6 x 1.0 Screw boot PLEASE CALL

9 80uF/250VAC 50/60Hz Capaciter PLEASE CALL

10 32D d17 Rubber grommet PLEASE CALL

11 20D x 10L M5 Rubber stop PLEASE CALL

12 35DX120L Handle with rubber sleeve PLEASE CALL

13 (3/8)M10 x 25 x 2T Teflon washer PLEASE CALL

14 M5 x 10 x1T Narrow washer PLEASE CALL

15 M14 x 26 x2T Wide washer PLEASE CALL

16 M4 x 8 x 1T Narrow washer PLEASE CALL

17 M14 Spring Lock Washer PLEASE CALL

18 M4 Spring Lock Washer PLEASE CALL

19 13mm OD hose clip PLEASE CALL

20 M4 x 0.7 x 12L Cross screw PLEASE CALL

21 M4 x 0.7 x 25L Cross screw PLEASE CALL

22 Female M10 X 1.5 Knob PLEASE CALL

23 M6 x 1.0 x 30L Knob PLEASE CALL

24 M14 x 2.0 Nut PLEASE CALL

25 M8 x 1.25 x 16L Hex Flange bolt PLEASE CALL

26 M10 x 1.5 x 260L x 2S Socket head cap hex screw PLEASE CALL

27 M10 Wide washer PLEASE CALL

28 M10 x 1.5 Nylon nut PLEASE CALL

29 M4 x 0.7 x 10 Countersunk cross screw PLEASE CALL

30 M4 x 0.7 x 10L Hex bolt PLEASE CALL

31 Capacitor housing PLEASE CALL

32 Gasket PLEASE CALL

33 Capacitor housing cover PLEASE CALL

34 Fan cover PLEASE CALL

35 Fan PLEASE CALL

36 PG-13.5 Cable gland PLEASE CALL

37 PG-11 Cable gland PLEASE CALL

38 M4 x 0.7 x 14L Cross screw PLEASE CALL

39 M5 x 0.8 x 16L Cross screw PLEASE CALL

PART NAME PART NUMBER

CUTTING HEAD ASSEMBLY

xxiii. REPLACEMENT PARTS LIST

Summary of Contents for VX10RSPRO

























Search results

Summary of Contents for VX10RSPRO

Reviews:

Related manuals for VX10RSPRO

Brands by name

Popular brands

Pearl VX10RSPRO, Owner'S/Operator'S Manual

Search results

Summary of Contents for VX10RSPRO

Reviews:

Related manuals for VX10RSPRO

Brands by name

Popular brands