manualshive.com logo in svg

PCE Instruments PCE-VM 25, User Manual

Share
Download
PCE Instruments PCE-VM 25 User Manual Download Page 30

Address:East Room 306,3th Floor,1st Building,Shenhua Industrial Park,Meihua Road, Futian District,Shenzhen City

Tel:0755-32978297

Email:[email protected]

Attention: Considerably loud volume levels can occur, especially when the sensor is moved, which can potentially lead to hearing damage. Before positioning the
vibration transducer always reduce the volume level or remove the headphones.

12. Reset Key

If it occurs that the PCE-VM 25 does not respond to the press of any button, press the reset key to restart the instrument. The reset key is reached with a thin object
through the aperture next to the type label (Figure 45).

Figure 45: Reset key

Saved data and settings are not lost when the instrument is reset.

13. Connection to a PC

The PCE-VM 25 has a USB port. For connection to a PC the VM2x USB cable is provided (Figure 46), which is connected to the 8 pin socket on the PCE-VM 25.
Switch the instrument off before connecting it to the PC.

Figure 46: USB cableVM2x-USB

Connect the other end of the cable to a USB port of the computer and switch the PCE-VM 25 on again. If the instrument is being connected with a particular computer
for the first time, a driver installation will be necessary.
The driver can be found on our website: https://www.pce-instruments.com/english/software-and-driver-download-win_4.htm
Unpack and save both data files in a directory on your computer. When Windows requests details of the source of the device driver, this directory should be entered.
The device driver is digitally signed and runs with Windows.

14. Firmware Update

The instrument software (Firmware) can be updated via the USB port. First of all, check whether a more up-to-date version than currently installed is available. To view
the latest version visit our ‚Software Download‘ site: https://www.pce-instruments.com/english/software-and-driver-download-win_4.htm
Here you will see the most recent firmware version available. The version number is composed of three digits for the hardware and three for the software (hhh.sss).
Only the last three digits are relevant for the firmware. The version currently installed in your instrument is displayed on the start screen.

EN - 30

Summary of Contents for PCE-VM 25




































Reviews:

No comments

Brands by name

Popular brands

Load more brands