Model Number
699B02
HAND HELD SHAKER
Revision: C
ECN #: 49738
P erfo rm an ce
EN G L ISH
SI
Operating Frequency(± 1 %)
159.2 Hz
159.2 Hz
Acceleration Output(± 3 %)
1 g rms
9.81 m/s² rms
[1]
Velocity Output
0.39 in/sec rms
9.81 mm/s rms
[2]
Displacement Output
0.39 mil rms
9.81 µm rms
[2]
Transverse Output
≤ 3 %
≤ 3 %
Distortion(0 to 250 grams load)
7 %
7 %
[3]
Maximum Load
8.8 oz
250 gm
[4]
Automatic Switch Off Time
1.0 to 2.5 minutes
1.0 to 2.5 minutes
[5]
Calibration Cycles(250 gram load)
90 cycles
90 cycles
[6]
En viro n m en tal
Temperature Range(Operating)
15 to 130 °F
-10 to 55 °C
Electrical
Ramp-Up time
≤ 3 sec
≤ 3 sec
[7]
Power Required(Standard)
Internal Battery
Internal Battery
Power Required
(Alternate)
DC Power
DC Power
Internal Battery(Quantity)
4
4
Internal Battery
(Type)
AA
AA
[8]
DC Power(± 5 %)
12 VDC
12 VDC
DC Power
1.67 Amps
1.67 Amps
Battery Life(250 gram load)
2.3 hours
2.3 hours
[6]
P h ysical
Size - Height
7.8 in
200 mm
Weight(with batteries)
31 oz
900 gm
[7]
Mounting Thread
1/4-28 Female
No Metric Equivalent
[9][10]
Mounting Torque(Maximum)
to 10 in-lb
to 10 in-lb
[9]
Size - Diameter
2.2 in
56 mm
[11]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Piezotronics, Inc.
OP TION A L VERSION S
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
N OTES:
[1]Unit supplied set to rms; see manual for peak selection.
[2]Calculated values for reference only.
[3]Typical max for range
[4]For sensors weighing <75 grams add model 080A136 mass
[5]Unit supplied set to auto shut off; see manual for continuous use selection.
[6]Approximate values, based on automatic switch off time and dependent on type of batteries.
[7]Typical.
[8]Alkaline type recommended for longest service life.
[9]Transducer to shaker table.
[10]Test sensor should be hand tightened (without tools).
[11]See PCB Declaration of Conformance PS022 for details.
Date: 07/10/2019
Date: 07/10/2019
Date: 07/10/2019
Date: 07/10/2019
67896
Entered: LK
Engineer: BAM
Sales: MC
Approved: BAM
Spec Number:
P h o n e: 800-959-4464
F ax: 716-684-3823
E-M ail: im i@ p cb .co m
3425 Walden Avenue, Depew, NY 14043
SU P P L IED A C C ESSORIES:
Model M081A19 Mounting stud, 1/4-28 to M6 x 1, SS with shoulder (1)
Model 073A15 Battery Pack (1)
Model 080A136 Calibration Mass (1)
Model 081A08 Mounting Stud (10-32 to 1/4-28) (1)
Model 081A40 Mounting Stud (2)