background image

3

HARDWARE CONFIGURATION

This motherboard is based on the one of three option --- Intel® 82440BX, Intel®
82440ZX or VIA® VT82C693 chipset. The chipset is a highly integrated solution
for a cost-effective and compact motherboard. The motherboard supports
standard DIMM module, PC-100 DIMM module or Registered DIMM Module.
Features on-board include super-I/O, Ultra DMA33, PCI bus master IDE, AGP
Ver 1.0, PCI Ver 2.1 compliance, USB, VRM 8.4 compliance, ECC, ATX specification
1.0 compliance, hardware monitoring (optional), On-board Sound Sub-system
(optional).(Notice: Intel® 82440ZX No Registered DIMM Support, No ECC).
This motherboard is ready for PC99 requirements.

Key Features
Processor

Full support for the Intel

®

 Pentium

®

 II & Intel

®

 Pentium

®

 III, Intel

®

 Celeron

®

and Deschutes

® 

processors using Slot 1 connector.

Slot 1 connector for Intel

®

 Pentium

®

 II & Intel

®

 Pentium

®

 III micro processors.

Supports 66MHz and 100MHz bus speed including all Pentium

®

 II &

Pentium

®

 III processors and future processor.

CPU Speed Setting

Jumper setting or no jumper is needed to set for various speed of CPU
(Factory optional).

VRM (Voltage Regulator Modules) on Board

Flexible motherboard design with on-board VRM 8.4, easy to upgrade
with Future Intel

®

 Pentium

®

 II & Pentium

®

 III processors.

Cache

Pentium

®

 II & Pentium

®

 III Processor built-in L2 cache.

System Memory

Up to 256MB (SDRAM) - for 440ZX only.

Up to 384MB (SDRAM) or 768MB (Registered SDRAM) - for 440BX, VIA.

A total of two 168-pin DIMM sockets for 440ZX.

A total of three 168-pin DIMM sockets for 440BX, VIA.

Supports SDRAM (Only for 66MHz Bus speed).

Supports PC-100.

Memory Organization

  • Supports single-density DIMMs of 1MB, 2MB, 4MB, 8MB and 16MB depth

(x64 or 72).

Supports double-density DIMMs of 2MB, 4MB, 8MB, 16MB and 32MB
depth (x64 or 72).

Supports error checking correction (ECC) using parity DRAM modules
(for 440BX, VIA).

Banks of different DRAM types depths can be mixed.

PC97/98/99

PC97/98/99 ready.

Expansion Slots

Supports SB-LINK Port for creative Sound PCI Card(VIA no support).

1 AGP slot (ver. 1.0, 1x/2x mode supported).

5 PCI bus master slots (rev. 2.1 compliant, with 1 PCI slot sharing with
1 ISA slot) - for 440BX, VIA.

Hardware Setup

Summary of Contents for 35895100 Series

















Reviews: