background image

13

Integrated

This section page includes all the items of IDE hard drive

Peripherals

and Programmed Input / Output features.

Supervisor /

Changes, sets, or disables password. It allows you to limit

User Password access to the system and the Setup Program.
Setting

IDE HDD Auto

Automatically detects and configures the hard disk parameters.

Detection

The Award BIOS includes this ability in the event you are
uncertain of your hard disk’s parameters.

Save & Exit

Saves value changes to CMOS and exits setup.

Setup

Exit Without

Abandons all CMOS value changes and exits setup.

Save

Standard  CMOS  Setup

The items in Standard CMOS Setup Menu are divided into 10 categories. Each
category includes one or more setup items. Use the arrow keys to highlight the
item and then use the <PgUp> or <PgDn> key to select the desired value in
each item.

ROM PCI/ISA BIOS

STANDARD CMOS SETUP

AWARD SOFTWARE. INC.

Date  (mm:dd:yy)

: Thu, Jan 23 1997

Time (hh:mm:ss)

: 00:00:00

HARD DISKS

TYPE SIZE CYLS. HEADS PRECOMP LANDZ SECTORS

Mode

Primary Master

: None 0

0

0

0

0

0

---

Primary Slave

: None 0

0

0

0

0

0

---

Secondary Master : None 0

0

0

0

0

0

---

Secondary Slave

: None 0

0

0

0

0

0

---

Drive A :

1.44M, 3.5 in

Base Memory

: 640K

Drive B :

None

Extended Memory

: 15360K

Video :

EGA/VGA

Other Memory

: 384K

Halt on :

All Errors

Total  Memory

: 16384K

Esc : Quit

éêèç

: Select Item

PU/PD/+/-  :  Modify

F1 : Help

(Shift) F2 : Change Color

(Note : The figures of BIOS Setup Menu included here only show a typical
case, and may not be exactly the same as the one on your unit.)

Date

The date format is <day-of-the-week>. <day> <month> <year>.
Press <F3> to  display the calendar.

Time

The time format is <hour> <Minute> <second> displayed in
24-hour military-time clock. For example, 1 p. m. is displayed
as 13:00:00.

BIOS Setup

Summary of Contents for 35895100 Series

















Reviews: