background image

8

Technical Reference Booklet

1

1

1

1

Warning:

Before handling the motherboard from its original package, please
ensure that there is no static electricity on your body. Otherwise it
may cause damage to the integrated circuits on the motherboard.

JP8, JP23 - BIOS Program Voltage / BIOS Select

JP8

JP23

Selection

(1-2)

(1-2)

INTEL (1MB)

(1-2)

(2-3)

MX (1MB)

(2-3)

(2-3)

ATMEL/SST/Winbond (1MB)

(2-3)

(2-4)

ATMEL/SST/Winbond (2MB)

JP8 & JP23 are pre-installed in the factory. They should NOT be altered by
the users.

Close        Open

Keyboard Password Power On

This motherboard provides a special security feature of keyboard password
power on. The feature is enabled in Integrated Peripherals Menu of CMOS
setup. There are two modes of operations.

(1) Single Key Turn On - if you set a single key password, the system will

turn on immediately after you press the password key.

(2) Keys Sequence Turn On - if you set a password with more than one

character, ie. a combination of keys, the system will turn on after you
press the password key sequence and then a <enter>.

Please notice that the power button will have no function if the keyboard
password power on feature is enabled.

JP29 - Keyboard Power Select

JP29

Selection

(1-2)*

Powered by +5V *

(2-3)

Powered by +5V Standby
(Allows Keyboard Power On)

1

1

* =Default setting

Summary of Contents for 35895100 Series

















Reviews: