manualshive.com logo in svg

Pavone Systems DAT 1400, Technical Manual

Share
Download
Pavone Systems DAT 1400 Technical Manual Download Page 50

Page 48

WEIGHING PARAMETERS

The parameters in this menu permit adjustment of the times for acquisition and updating of the display 

and manual or automatic resetting by the transmitter.

uSE

INSTRUMENT OPERATION 

Selecting the operation of the instrument. In case of a change from FREE operation to METRIC operation, 

to confirm the setting authentication is required through the password of authorised personnel.

Value  

Variation

Free  

Free operation. [0]

Trade 

METRIC instrument operation. [1]

Default: Free

Not1on

STABILITY OF WEIGHT [1303]

This parameter defines the number of divisions needed to consider the weight stable.
A high number of divisions allows the transmitter to quickly detect stability of the weight, which is nee-

ded when executing tare and print commands.

Value  

Variation

0 

Weight always stable

1 

Stability determined quickly

2 

Stability determined with medium parameters

3 

Stability determined accurately

4 

Stability determined with the highest accuracy

Default: 2

AUto-0

AUTOZERO WHEN SWITCHING ON [1304-1305]

This parameter defines the value of maximum weight that can be reset when the instrument is switched on.
This operation corresponds to zero calibration of the system andis executed only if the weight is stable 

and below the set value.

Value: from 0 to Capacity.
Default: 0

Summary of Contents for DAT 1400

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands