manualshive.com logo in svg

Pavone Systems DAT 1400, Technical Manual

Share
Download
Pavone Systems DAT 1400 Technical Manual Download Page 20

Page 18

INFO DISPLAY

PdAt01 

  

When the instrument is switched ON, a display test is run followed by the identifica-

tion code and then the version of the software, in that order. These codes are to be 

cited when requesting assistance 

When is not in progress a programming procedure, the display shows the weight measured in kilograms. 

Under certain conditions, the following messages are reported:

NOTIFICATION OF ERRORS

In operating mode, the following error codes may appear on the display.

Fixed message

P 

<picco>

 

Display of peak value.

rENotE 

  

Communication with “Optimation” PC utility software.

ϩϩϩϩϩϩ

   Overload. The load applied to the load cells exceeds by over 9 divisions the maximum 

capacity of the weighing system.

 O-L 

   Signal that the load cells are absent or outside of the measuring range mV/V.

Flashing message, alternating with the weight measured. 

No CAL

   Calibration weight not performed)

No CoN

   Fieldbus network disconnected 

E-F.buS

   Fieldbus interface absent or not working.

Summary of Contents for DAT 1400

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands