manualshive.com logo in svg

Pavone Systems DAT 1400, Technical Manual

Share
Download
Pavone Systems DAT 1400 Technical Manual Download Page 31

Page 29

SySt.FS

CAPACITY OF THE WEIGHING SYSTEM [1301-1302]

Programming the useful capacity (net) of the weighing system.

Values: from 0 to Load Cell Capacity 
Default: 0

dEAd L.

FIXED TARE OF WEIGHING SYSTEM [1106-1107]

Programming the fixed tare value of the weighing system

Values: from 0 to Capacity Value
Default: 00000

CAL.tyP

SELECTING THE CALIBRATION TYPE

Selecting the calibration type. On confirmation one of the following procedures is started. 

dEAd W

DEAD WEIGHT TYPE CALIBRATION [501÷503]

Zero Calibration and Full Scale up to 5 linearisation points using Sample weights. 

tAbLE

TABLE TYPE CALIBRATION [1151÷1172]

Allows you to manually program up to 5 calibration points. The values corresponding to those resulting 

from the linearisation procedure with sample weights. In this way you can copy the calibration values 

made with sample weights.

PARAMETERS DISPLAYED ONLY DURING METRIC OPERATION 

G-CAL

CALIBRATION LOCATION GRAVITY [1108-1109]

Programming of the force of gravity of the location where the calibration takes place. 

Values: from 9.77000 to 9.84000
Default: 0

G-uSE

GRAVITY OF LOCATION OF USE [1110-1111]

Programming of the force of gravity of the location where the instrument will be used. 

Values: from 9.77000 to 9.840000
Default: 0

Summary of Contents for DAT 1400

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands