background image

6

Universal Concentric Vent Kit

[Stock Code: 1819]

Low Profile Termination Kit

2 in.: [Stock Code: 1820]

3 in.: [Stock Code: 1820-1]

ULC S636 / UL 1738 

certified for use in both 

Canada and USA

Plastic Rain Cap

[Stock Code: 1821]

Not approved for use in 

Canada.

Neutralizer (× 1)

[Stock Code: 1822]

Manifold Kit (× 1)

[Stock Code: 1827]

2.3  Field  Purchased Accessories

Service Valve Kit 

with Pressure Relief Valve (1 each)

Not supplied from PB Heat. Isolation valves may be 

purchased separately from an authorized wholesaler. 

The following are required specification for Isolation 

valves.

1.  Comply with Lead Free installation requirement.

2.  Certified to NSF/ANSI 61.

3.  Shall facilitate isolation of the Combi Boiler from the 

water line.

4. 3/4” FTP Unions for connection to Combi Boiler.

5.  3/4” size connection for water lines (Cold and 

Domestic hot water lines).

6.  Equipped with purge and drain valve for hose 

connection and tethered brass cap.

7.  Equipped with the 3/4” connection for optional 

pressure relief valve (150psi). 

Scale Inhibitor (1 each)

Damage to the Heat 

Exchanger caused by Scale 

Build-up is not covered 

by the Pavilion Limited 

Warranty.

To prevent the Heat 

Exchanger damage, the 

water must be treated with 

a Southeastern Filtration 

Scale Stick

TM

, 3M Aqua-

Pure

TM

 scale inhibitor, 

or other scale inhibitor 

system.  

About the Combi Boiler

Summary of Contents for GHQ-C3201WX-FF PB US





















































































Reviews: