background image

5.0  OPERATION

Once the Model 1092ARC is properly configured and installed, it

should operate transparently.  This sections describes functions of the
LED status indicators, and the use of the built-in loopback test modes.  

5.1  LED STATUS INDICATORS

The Model 1092ARC features twelve front panel LEDs that monitor

power, the DTE signals, network connection and test modes.  Figure
11(below) shows the front panel location of each LED.  Following Figure
11 is a description of each LED function. 

TD & RD

glow yellow to indicate an idle condition of Binary 
“1” data on the respective terminal interface 
signals.  Green indicates Binary “0” data.

CTS

consists of 2 LEDs, 1 yellow, 1 green.  CTS glows 
green to indicate that the Clear to Send signal from
the modem is active.  Yellow indicates inactive 
CTS.

CD

consists of 2 LEDs, 1 yellow, 1 green.  CD  glows 
yellow if no carrier signal is being received from the
remote modem.  Green indicates that the remote 
modem’s carrier is being received.

DTR

glows green to indicate that the Data Terminal 
Ready signal from the terminal is active.

30

Figure 11. The Model 1092ARC Series' front panel LEDs

Model 1092ARC

Note: LEDs described as yellow are red in earlier
versions of the 1092ARC.

The RJ-45 connector on the Model 1092ARC’s twisted pair interface

is polarity insensitive and is wired for a two-wire interface.  The
signal/pin relationships are shown in Figure 9 below.

3.  

Proper 

2-Wire Pairing between the two modems is as follows:

SIGNAL

PIN#

PIN#

SIGNAL

TIP

4--------------------------------------------- 4

TIP

RING

5--------------------------------------------- 5

RING

4.  

Proper 

4-Wire Pairing 

between the two modems is as follows:

SIGNAL

PIN#

PIN#

SIGNAL

Tx

4--------------------------------------------- 3

Rx

Tx

5--------------------------------------------- 6

Rx

Rx

3--------------------------------------------- 4

Tx

Rx

6--------------------------------------------- 5

Tx

4.3.4 

Connection to the Control Port Interface

Please refer to the Model 1001CC Control Card user manual for

cable requirements of the Control Port Interface.  

29

Figure  10. Model 1092ARC twisted pair line interface.

1 (N/C)
2 (GND)
3 (4-Wire Rx)
4 (2-Wire TIP/4-Wire Tx)
5 (2-Wire RING/4-Wire Tx)
6 (4-Wire Rx)
7 (GND)
8 (N/C)








Summary of Contents for 1092ARC





















Reviews: