background image

The table below provides an overview of interface strap functions

for the rear interface cards.  Following the table overview are detailed
descriptions of each strap’s function.

DTE Shield (DB-15 Pin 1) & FRGND (JB3)

In the connected position, this strap links DB-15 pin 1 & frame

ground.  In the open position, pin 1 is disconnected from frame ground. 

JB3

Position 1&2  =  DTE Shield (Pin 1) and FRGND Connected
Position 2&3  =  DTE Shield (Pin 1) and FRGND Not Connected

Figure 8.

1001RCM11545 strap locations

INTERFACE CARD STRAP SUMMARY TABLE #2

Strap

Function

Position 1&2

Position 2&3

JB3

DTE Shield (Pin1) & FRGND

Connected*       Open

JB4

FRGND & SGND (Pin 8)

Connected*

Open

* Indicates default setting

24

3.3.2  Model 1001RCM13445 Rear Card Strap Settings

Figure 7 shows the strap location for the Model 1001RCM13445

(M/34/RJ-45) rear card. This strap determines whether Signal Ground
and Frame Ground will be connected.  

SGND & FRGND (JB4)

In the connected position, this strap links Signal Ground and frame

ground. In the open position, signal ground is disconnected from frame
ground.

JB4

Position 1&2  =  SGND and FRGND Connected*
Position 2&3  =  SGND and FRGND Not Connected

*

indicates default setting

3.3.3 Model 1001RCM11545 Rear Card Strap Settings

Figure 8 shows strap locations for the Model 1001RCM11545 (DB-

15) rear cards.  These straps determine various grounding
characteristics for the terminal interface and twisted pair lines. JB3 and
JB4 are user configurable.  

23

Figure 7. M/34/RJ-45 strap locations

JB4

123

Summary of Contents for 1092ARC





















Reviews: