background image

APPENDIX B

MODEL 1045RC CABLE RECOMMENDATIONS

The Patton Model 1045RC operates at frequencies of 64KHz or less

and has been performance tested by Patton technicians using twisted-
pair cable with the following characteristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

To gain optimum performance from the Model 1045RC, please keep

the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of  20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher 
AWG numbers than 26)

• Use of twisted pair with a resistance greater than the above 
specifications may cause a reduction in maximum distance 
obtainable.  Functionality should not be affected.

• Environmental factors too numerous to mention can affect the 
maximum distances obtainable at a particular site.  Use the above 
data rate/distance table as a 

general guideline only.

21

APPENDIX C

MODEL 1045RC FACTORY REPLACEMENT PARTS

The Patton Model 1045RC rack system features interchangeable

rear cards, power cords/fuses for international various operating
environments and other user-replaceable parts.  Model numbers,
descriptions and prices for these parts are listed below:

Patton Model #

Description

1000RPEM..........................120/240V Rear Power Entry Module
1000RPSM-2.......................120/240V Front Power Supply Module
1000RPEM-DC ...................DC Rear Power Entry Module
1000RPSM-48A ..................48V Front Power Supply Module
1000RPEM-V ......................120/240V CE Compliant Rear Power 

Entry Module

1000RPSM-V ......................120/240V CE Compliant Front Power 

Supply Module

0805US ...............................American Power Cord
0805EUR.............................European Power Cord CEE 7
0805UK ...............................United Kingdom Power Cord
0805AUS.............................Australia/New Zealand Power Cord
0805DEN.............................Denmark Power Cord
0805FR ...............................France/Belgium Power Cord
0805IN.................................India Power Cord
0805IS.................................Israel Power Cord
0805JAP..............................Japan Power Cord
0805SW ..............................Switzerland Power Cord

0516FPB1 ...........................Single Width Blank Front Panel
0516FPB4 ...........................4-Wide Blank Front Panel
0516RPB1...........................Single Width Blank Rear Panel
0516RPB4...........................4-Wide Blank Rear Panel

056S1..................................Set of 16 #4 pan head screws/washers

22

Summary of Contents for 1045RC














Reviews: