background image

4.3.1  TERMINAL INTERFACE CONNECTION

The Model 1045RC is wired as a DCE, and allows for three possible

terminal interface connections: 

RS-232C/V.24 (electrical) + DB-25 female (physical)

V.35/RS-530 (electrical) + DB-25 female (physical)

V.35 (electrical) + M/34 female (physical)

To select the appropriate 

electrical interface, please refer to

Section 3.1.4 of this manual.  To select or construct a cable with the
appropriate

physical interface pin-outs, please refer to the diagrams in

Appendix D and Appendix E of this manual.

4.3.2  TWISTED PAIR CONNECTION

The Model 1045RC supports communications between RS-232 or

V.35 devices  at distances to 6 miles and data rates up to 64 Kbps.  The
Model 1045RC is designed to operate in a closed data circuit with other
1045RCs or 1045 plug-in units.

To function properly, the Model 1045RC needs two twisted pairs of

unconditioned, dry metallic wire between 19 and 26  AWG (higher
number gauges may limit distance somewhat).  Both shielded and
unshielded wire yield favorable results.  Flat modular telephone type
cable, dial-up analog circuits or leased lines that run through
signal/equalization equipment are NOT acceptable.  For further
information about acceptable wire grades, please refer to the diagram
in appendix B.

Point-to-Point Twisted Pair Connection

The 6-position RJ-11 and 8-position RJ-45 jack options for the

Model 1045RC are prewired for a standard TELCO wiring environment.
Connection of a 2-wire or 4-wire twisted pair circuit between two or
more Model 1045RCs requires a 

crossover cable as shown in the

following diagrams.

15

RJ-11/4-Wire

SIGNAL

PIN#

PIN#

SIGNAL

GND

1

6 .......................GND

RCV-

2

4 .......................XMT-

XMT+

3

5 .......................RCV+

XMT-

4

2 .......................RCV-

RCV+

5

3 .......................XMT+

GND

6

1 .......................GND

RJ-45/4-Wire

SIGNAL

PIN#

COLOR

COLOR

PIN#

SIGNAL

GND

2

7.......................GND

RCV-

3

5.......................XMT-

XMT+

4

6.......................RCV+

XMT-

5 3

RCV-
RCV+

6

4.......................XMT+

GND

7

2.......................GND

Connection to ground is optional

Standard color codes—yours may be different

The Model 1045RC is not sensitive to polarity

AT&T standard modular color codes

16

1 - Blue
2 - Orange
3 - Black
4 - Red
5 - Green
6 - Yellow
7 - Brown
8 - Slate

1 - Blue
2 - Yellow
3 - Green
4 - Red
5 - Black
6 - White

Notice!

Any modular twisted pair cable connected to the

Model 1045RC must be shielded cable, and the outer shield
must be properly terminated to a shielded modular plug on both
ends of the cable.

Notice!

Any terminal cable connected to the Patton Model

1045RC must be shielded cable, and the outer shield must be
360 degree bonded–at both ends–to a metal or metalized
backshell.

Summary of Contents for 1045RC














Reviews: