123
124
GB
GB
WARNING:
The guard must be properly
installed. The guard provides partial
protection from the risk of thrown objects to
the operator and others.
NOTE:
If guard is not properly installed,
damage to unit (including motor failure) will
result.
IV- Assembly instructions
1. Place unit on a flat surface.
2. Push the auxiliary handle over the handle
mounting location. Reinstall bolt in handle.
3. Adjust forward or backward to a
comfortable position; tighten bolt securely.
.(see below Fig.A)
(See below Fig D1 D2)
Loose the knob in the direction indicated by
the unlock sign – adjust the tube length to
your desire- secure the knob.
2 Before switching on, push a loop of cable
through the space in the handle and
secure it over the cable restraint.
(see below Fig.B)
1. Insert the flower guard into the slot on the
motor housing
2. Insert the safety guard into the slot on the
motor housing
3. Screw tight the Guard.
2
Installation the safety guard and flower
guard
1
Installation of the auxiliary handle
V- Operating instructions
1
Tube length adjusting
1 To prevent excessive strain on the cable
connections, the trimmer is fitted with a
cable restraint.
3
Mains supply cable strain relief
(see below fig c1)
3
Operating the on/off switch
2
Operating the edging switch
(See below Fig E1, E2)
Pull the Edging switch away from the motor
house as indicated by “E1”, then rotate 180
degrees as indicated by”E2” to the edge
cutting mode.
(See below Fig C2)
First press the locking button in then press
the on/off switch ,your switch is now on.
To switch off, simply release the on/off
switch.
WARNING!
Do not use the product without
fitting the guard.
WARNING!
The cutting head continues to rotate
after the trimmer has been switched off, wait
until it has stopped then lay down the tool.
WARNING!
Always wear eye protection .Never
lean over the trimmer head. Rocks or debris
can ricochet or be thrown into eyes and face
and cause blindness or other serious injury.
When operating unit, check for the following:
Wear eye protection and heavy clothing .
Hold front handle with one hand and
auxiliary handles with the other hand.
Keep unit below waist levels. Work only
from your right to your left to ensure debris
is thrown away from you.
Without bending over, keep line near and
parallel to the ground(perpendicular when
edging).Do not switch the machine on with
the cutting head on or near material to be
cut.
Ensure the cutting line is at full speed before
contacting material to be cut.
WARNING!
Make sure that line is fed out before
operation. Make sure motor is up to full
speed before trimming.
1. Let the trimmer run for a few seconds
without touching the working area, and
allow the trimmer to cut the line.
2. Use the trimmer at an angle of
approximately 15 degree to the working
area.
3. Swing the trimmer head from side to
side.(See below Fig.F)
4. If the grass is very long cut in stages
rather than trying to cut in one ago. Do not
overload your trimmer ,take small cuts this
will keep machine operating at high speed
and will greatly improve cutting
efficiency.(see below Fig.G)
(See below Fig.H)
If required, line can be fed out manually. To
operate, press and release manual line feed
button, while gently pulling out the lines until
the lines reach the line cutter.
When the required amount of line is fed out,
gently pull on the second line (there is no
need to press the manual line feed button
again),If the line extends past the line cutter,
too much line has been fed out.
If too much line is fed out, remove the spool
cap and turn spool counter-clockwise until
the line is at the desired length .
4
To manually feed the line
5
To remove the cutting head cover
(See below Fig.I)
Press the release latch on the spool head
cover and remove cover, pulling it straight
off the cutting head assembly.
Pull the cutting head cover away from the
spool holder.
(See Fig.J)
Keep all areas of the cutting head cover and
spool holder clean .
Replace the spool head cover, pressing
firmly down towards the spool holder to
ensure the cover is fully located.
Check that the cap is correctly fitted by
trying to remove it without depressing the
two latches.
6
When refitting the spool cap
7
To replace cut line
For your convenience it is recommended
you buy spool and line complete.
