Parts Connect IM70 User Manual Download

Page: 26 / 30

ERROR CODES

Error

Code

Error Status

Reason

Treatment

lights

E01

1. Ice full swivel is not

functioning correctly

2. Ice full switch is not

functioning properly

1. Ice full swivel is jammed

2. Ice full switch needs to be

replaced

1. Free swivel of jam.

2. Replace ice full switch

Error

Light

E03

Maximum harvest time

of 3 minutes has been

exceeded.

1. Reversing valve problems.

2. Ice cube thickness setting

is too thin.

3. Lack of water.

4. Condenser is too cold.

1. Fix the reversing valve.

2. Set ice cube to normal

thickness.

3. Check water inlet valve.

Error

Light

E02

Ice making shall con-

tinue for 10 cycles, max-

imum time of 40 minutes

has been exceeded.

1. Ambient temperature is too

high.

2. Condenser is too hot.

3. Refrigerant is leaking.

4. Lack of water.

1. Check if condenser is too

hot. Clean it (Page 22) &

make sure the fan is oper-

ating properly.

2. Repair refrigerant leak.

3. Check water inlet..

Error

Light

E04

High temperature error

for condenser.

1. Ambient temperature too

high.

2. Fan is not functioning.

3. Dust on the condenser.

1. Fix the fan.

2. Clean the condenser.

Error

Light

E05

Lack of water.

1. Water supply pressure low.

2. Water valve broken, or

water tank leaking.

3. Water sensor is not working.

1. Fix water supply system.

2. Fix the valve or tank.

3. Change the sensor.

Error

Light

E07

Condenser temperature

sensor open.

Sensor broken or terminal is

not connected.

Check and fix sensor.

E08

Condenser temperature

sensor shorted.

Sensor broken or terminal

shorted

Check and fix sensor.

E09

Evaporator temperature

sensor open.

Sensor broken or terminal is

not connected.

Check and fix sensor.

E10

Evaporator temperature

sensor shorted.

Sensor broken or terminal

shorted.

Check and fix sensor.

E11

After 30 minutes of the

icemaking procedure,

the evaporator tempera-

ture still higher than

0ºC.

1. Compressor problem.

2. Refrigerant leaking.

3. Condenser is too hot.

1. Repair the compressor.

2. Repair refrigerant leak.

3. Repair the condenser fan

or clean the condenser.

Error

Light

Note: After correcting the problem, short press the Mode button. The ice machine will run properly.

Summary of Contents for IM70































Search results

Summary of Contents for IM70

Reviews:

Related manuals for IM70

Brands by name

Popular brands

Parts Connect IM70, User Manual

Search results

Summary of Contents for IM70

Reviews:

Related manuals for IM70

Brands by name

Popular brands