23
GB/IE
Wear safety gloves when changing the saw blade.
Risk of injury!
•
Swing up the machine head (5).
•
Undo the screw (e) on the guide bar (37), so that it can
move freely and be pivoted downwards.
•
Press the release lever (3). Swing up the saw blade
guard (6) to the point where the recess in the saw
blade guard (6) is above the flange bolt (31).
•
Press the saw shaft lock (4) with one hand. With the
other hand insert the allen key (d) in the flange bolt (31).
•
Hold the Allen key (d) and slowly close the saw blade
guard until it touches the Allen key.
•
Firmly press the saw shaft lock (4) and slowly rotate the
flange bolt (31) in clockwise direction. The saw shaft lock
(4) engages after no more than one rotation.
•
Now, using a little more force, slacken the flange
bolt (31) in the clockwise direction.
•
Turn the flange screw (31) right out and remove the
external flange (32).
•
Take the blade (7) off the inner flange (38) and pull
out downwards.
•
Carefully clean the flange screw (31), outer flange (32)
and inner flange (38).
•
Fit and fasten the new saw blade (7) in reverse order.
•
Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (7)
must coincide with the direction of the arrow on the
housing.
•
Move the guide bar (37) into position and tighten the
screw (e) again.
•
Before continuing your work make sure that all safety
devices are in good working condition.
•
Important! Every time that you change the saw blade
(7), check to see that it spins freely in the table insert
(11) in both perpendicular and 45° angle settings.
•
Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 3/19/20)
•
To switch on:
Move the ON/OFF switch of the laser
(34) to the “1” position. A laser line is projected onto
the material you wish to process, providing an exact
guide for the cut.
•
To switch off:
Move the ON/OFF switch of the laser
(34) to the “0” position.
•
Replacing the battery:
Switch off the laser (33).
Remove the battery compartment cover (36). Re-
move the batteries and replace with new batteries
(2 x 1.5 Volt Type LR 03 Micro, AAA) Check that
the battery terminals are positioned correctly when
inserting new batteries. Close the battery compart-
ment (35) again.
8.12 Adjusting the laser (Fig. 21)
If the laser (33) ceases to indicate the correct cutting line,
you can readjust the laser. To do so, open the screws
(38) and set the laser by moving sideways to that the
laser beam strikes the teeth of the saw blade (6).
9. Transport
•
Tighten the set screw (26) in order to lock the rotary
table (14)
•
Activate the release lever (3), press the machine
head (4) downwards and secure with the safety pin
(23). The saw is now locked in its bottom position.
•
Fix the saw’s drag function with the locking screw for
drag guide (20) in rear position.
•
Carry the equipment by the fixed saw table (15).
•
When reassembling the equipment proceed as de-
scribed under section 7.
10. Maintenance
m
Warning!
Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time us-
ing a cloth. In order to extend the service life of the tool, oil
the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
Brush inspection
Check the carbon brushes after the first 50 operating
hours with a new machine, or when new brushes have
been fitted. After carrying out the first check, repeat the
check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the spring
or contact wire are burned or damaged, it is necessary
to replace both brushes. If the brushes are found to be
usable following removal, it is possible to reinstall them.
11. Storage
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
12. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the
extension cable used must also comply with these
regulations.
•
The product meets the requirements of
EN 61000-3-11 and is subject to special connection
conditions. This means that use of the product at any
freely selectable connection point is not allowed.
•
Given unfavorable conditions in the power supply the
product can cause the voltage to fluctuate temporarily.
