10 GB/CY
Ensure you will have adequate space to
work in and will not put others at risk.
Always secure the product to the worktop
with screws of an adequate length and
thickness to always maintain control over
the product.
Product setup (see Fig. B)
- Required thickness of the edge of the table:
15–30 mm
- Drill diameter: 10.5 mm
- Size of screw: M10
Use the stop notches
9
to position the prod-
uct on the worktop
22
. The grinding base
8
must extend beyond the edge of the table.
Mark the bores with a pencil and remove
the product.
Now drill two holes in the worktop
22
.
Fasten the grinding base to the worktop us-
ing the included screws
23
, washers
24a
and nuts
24b
.
Assembling the product
(see Fig. C)
Screw the handle
4
to the grinding
head
2
.
Loosen the locking nut
10
on the chain ten-
sioner
12
.
Attach the chain tensioner
12
to the grind-
ing base
8
and tighten with the locking
nut
10
.
If applicable, attach the mains cable
17
inside the cable holder
16
.
Attaching the adjusting
screw (see Fig. C)
Before assembly, loosen the locknut
26
from
the adjusting screw
6
. Insert the locknut
26
to the grinding head
2
and screw the
adjusting screw
6
and washer
25
to the
locknut
26
.
Initial use
CAUTION! RISK OF INJURY!
Only use grinding discs and accessories
recommended by the manufacturer. Using
tools or accessories other than those recom-
mended in the instructions for use could
result in injury.
Never operate the product without visual
cover.
Do not use saw blades.
Always unplug from the mains before work-
ing on the product.
Inspect the grinding disc prior to use: Check
the clearance between the visual cover and
grinding disc.
Do not use damaged or deformed grinding
discs.
Do not switch on the product until it has
been firmly secured to the worktop.
CAUTION! RISK OF INJURY!
Wear eye and hearing protection.
Wear cut-resistant safety gloves
and, if necessary, an apron
when working on the saw chain
to prevent cuts.
Keep your hands away from the
grinding disc and cutting teeth
during use. Do not move the saw
chain by hand. Risk of injury.
Switching on and off
Note:
Verify the voltage specified on the
nameplate corresponds with the voltage of the
power source.
Note:
Perform a test run of at least 30 seconds
without load before using this product for the
first time and after changing the grinding disc.
Switch off the product immediately if the grind-
ing disc is out of round, considerable vibration
occurs or you notice abnormal noise.
Plug the mains cable into a
socket (note the mains voltage).
Summary of Contents for PSG 85 A1
