![background image](http://html2.mh-extra.com/html/parkside/psg-85-a1/psg-85-a1_translation-of-original-instructions_4165435011.webp)
11
GB/CY
Press the “I“ on switch (green)
1a
to switch
the product on.
Press the “0“ off switch (red)
1b
to switch
the product off.
The grinding disc will continue running after
switching off the tool. Risk of injury.
Note:
This product is equipped with an LED
lamp. The LED lamp
19
is switched on automa-
tically when the on switch
1a
is being pressed.
The LED lamp is switched off automatically
when the off switch
1b
is being pressed.
Note:
This product has start-up protection: The
product will not automatically restart after auto-
matically being switched off by voltage interrup-
tion or overload protection. To switch the
product on again, press the “I“ on switch
(green)
1a
and the product will start.
Sharpening a saw chain
(see Fig. D)
Note:
Be sure to keep the vents clear when
working in dusty environments (see “Mainte-
nance and Cleaning”).
If jammed, switch off the product
and unplug from the mains. Then
clear the jam.
An incorrectly sharpened saw chain may
damage the product and increase the risk
of saw kickback!
Be sure to accurately adjust the saw chain.
Observe the correct sharpening angle and
minimum chain size. Remove as little material
as possible.
Do not sharpen drive links (a) or tie straps
(b) or the saw chain may break. Failure to do
so poses a risk of accidents when using the
chain saw.
b
a
Note:
Clean the saw chain before sharp-
ening. Clean any greasy wood residue or
oil residue with a brush or rag.
Note:
All cutting links must be the same
length and width after sharpening.
Note:
The saw chain is worn and must be
replaced if the cutter tooth is only approx.
4 mm.
Inserting the saw chain:
Turn the clamping lever
13
counter-clock-
wise to open the chain guide. You will need
to return the clamping lever to the original
position several times to do so. To unlock
the clamping lever, pull the clamping lever
outward, then return to the original position
and allow to lock into position.
Insert the saw chain in the chain guide
7
.
The cutting edges must face the grinding
disc
18a
.
Flip down the stop
15
and pull the saw
chain toward the back until the cutting
tooth
27
to be sharpened makes contact
with the stop (see Fig. D1).
Adjusting the grinding angle:
Loosen the locking nut
10
and set the neces-
sary grinding angle α on the rotary table for
the chain tensioner
12
using the scale
11
.
Then tighten the locking nut
10
.
Note:
Use the grinding angle specified by
the manufacturer.
Adjusting the stop:
Move the grinding head
2
down on the
handle
4
with the motor switched off.
Use the chain feed adjusting screw
14a
to
move the cutting tooth
27
toward the grind-
ing disc
18a
until the cutting tooth makes
contact with the grinding disc (see Fig. D2).
Summary of Contents for PSG 85 A1
