Parker PSD1 Installation Instructions Manual Download Page 94

Page: 94 / 109

Technical data

94 (109)

192-011006N8 2019-07

09.10.19 09:27

In this chapter you can read about:

•

PSD1-S: Single device ............................................................................................................. 94

•

PSD1-M: Multi-axes system...................................................................................................... 96

•

Motors/ feedback/ motor holding brake ................................................................................... 100

•

Digital inputs / outputs (specifications) .................................................................................... 102

•

Technical data STO ................................................................................................................ 103

•

EC directives and applied harmonized EC norms (PSD1) ....................................................... 103

•

EMC limit values PSD1........................................................................................................... 103

•

Insulation requirements PSD1 ................................................................................................ 104

•

Environmental requirements PSD1 ......................................................................................... 104

•

cUL certification ...................................................................................................................... 104

•

EtherCAT characteristics ........................................................................................................ 104

•

PROFINET Characteristics ..................................................................................................... 105

•

Ethernet IP characteristics ...................................................................................................... 105

8.1

PSD1-S: Single device

In this chapter you can read about:

•

Mains connection PSD1-S ........................................................................................................ 94

•

Output data PSD1-S 1/3*230 VAC............................................................................................ 95

•

Control Voltage 24 VDC PSD1-S .............................................................................................. 95

•

Braking operation PSD1-S ........................................................................................................ 95

•

Size / weight of PSD1-S ........................................................................................................... 95

8.1.1.

Mains connection PSD1-S

Category

Specifications

PSD1-S

PSD1-S_1200

PSD1-S_1300

Mains voltage

3 phases 3* 230 VAC ±10%

30 ... 253 VAC / 50-60 Hz

Single Phase 230 VAC ±10%

30 ... 253 VAC / 50-60 Hz

Input Current

1AC230V: 6.8 Arms
3AC230V: 1.7 Arms

1AC230V: 11 Arms

3AC230V: 4.2 Arms

Maximum fuse per
device*

Single phase: 8 A

Three phases: 3 A

Fuse Class: gS (gRL), Time-delay

Single phase: 12 A

Three phases: 6 A

Fuse Class: gS (gRL), Time-delay

Earth leakage current

Current on the mains PE (see page 24) (>3,5 mA)

Supply networks

Possible supply networks (see page 24): TN

Circuit breakers for operation according to CE.
Circuit breakers for UL und CSA see Chapter UL (see page 18, see page 21).

Please observe the notes in chapter “

Operating conditions for CE-conform

operation

(see page 13)“.

8. Technical data

Summary of Contents for PSD1














































































































Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands

Parker PSD1, Installation Instructions Manual

Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands