Parker PSD1 Installation Instructions Manual Download Page 105

Page: 105 / 109

192-011006N8 PSD1 Installation Guide

192-011006N8 2019-07

09.10.19 09:27

105 (109)

8.12

PROFINET Characteristics

Category

Specifications

Profile

•

PROFIdrive profile drive technology V4.2

PROFINET Version

•

PROFINET IO (RT)

Transmission mode

•

100BASE-TX (Full Duplex)

Profinet ID

•

PSD1-S: 0x5331

PSD1-M: 0x4D78

Device master file

•

PSD1-S

http://www.Parker.com/Literature/Electromechanical

Europe/Downloads/GSDML-V2.3-Parker-PSD1S.zip

•

PSD1-M

http://www.Parker.com/Literature/Electromechanical

Europe/Downloads/GSDML-V2.3-Parker-PSD1M.zip

Realized application
class

•

AC 3 Positioning

8.13

Ethernet IP characteristics

Category

Specifications

Profile

DS402

Ethernet/IP

•

Generic device support for CIP and encapsulated layer

Ethernet

•

Several Ehernet interfaces are supported e.g., for devices with embedded

switch technology (for the support of linear or ring topology)

Connection established

•

Device Level ring (DLR) functionality is supported (announce based ring nod)

Connections

•

Simultaneous support for up to 10 I/O connections

•

Simultaneous support for up to 10 encapsulation sessions

•

Simultaneous support for up to 2 explicit messaging connections per

encapsulation session

•

Unconnected explicit messaging is supported

Service(s)

•

Quality of Service (QoS) supported

•

UDP for order list services, list targets and list identity for encapsulation protocol

available

•

Pv4 address conflict detection for EtherNet/IP devices

Device master file

•

PSD1

http://solutions.parker.com/psd_support

Product Code

•

PSD1S: 21297 (0x5331)

•

PSD1M_1: 19761 (0x4D31) (1 power stage)

•

PSD1M_2: 19762 (0x4D32) (2 power stages)

•

PSD1M_3: 19763 (0x4D33) (3 power stages)

Vendor code

•

Realized object grades

•

Identity

•

Message Router

•

Assembly

•

Connection manager

•

Device level ring

•

QoS

•

PSD1 object pool

•

TCP/IP Interface

•

Ethernet Link

Summary of Contents for PSD1














































































































Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands

Parker PSD1, Installation Instructions Manual

Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands