background image

Introduction 

 

 

 

 

24  (109)

 

192-011006N8 2019-07 

09.10.19 09:27 

 

 

2.10.6. 

Current on the mains PE (leakage current) 

 

 

This product can cause a direct current in the protective lead. If a residual current 

device (RCD) is used for protection in the event of direct or indirect contact, only 

a type B (all current sensitive) RCD is permitted on the current supply side of this 

product . Otherwise, a different protective measure must be taken, such as 

separation from the environment by doubled or enforced insulation or separation 

from the mains power supply by means of a transformer. Respect the supplier's 

instructions. 

 

Mains filters do have high leakage currents due to their internal capacity. An 

internal mains filter is usually integrated into the servo controllers. Additional 

discharge currents are caused by the capacities of the motor cable and the motor 

winding. Due to the high clock frequency of the power output stage, the leakage 

currents do have high-frequency components. Please check if the FI protection 

switch is suitable for the individual application. 

If an external mains filter is used, an additional leakage current will be produced. 

The figure of the leakage current depends on the following factors: 

 Length and properties of the motor cable 

 Switching frequency 

 Operation with or without external mains filter 

 Motor cable with or without shield network 

 Motor housing grounding (how and where) 

Remark: 

 The leakage current is important with respect to the handling and usage safety of 

the device. 

 A pulsing leakage current occurs if the supply voltage is switched on. 

Please note: 

The device must be operated with effective grounding connection, which must 

comply with the local regulations for high leakage currents (>3.5 mA). 

Due to the high leakage currents it is not advisable to operate the servo drive with 

an earth leakage circuit breaker. 

 

2.10.7. 

Supply networks 

This product is designed for fixed connection to TN networks (TN-C, TN-C-S or 

TN-S). Please note that the line-earth voltage may not exceed 300VAC.   

 When grounding the neutral conductor, mains 

voltages of up to 480VAC are permitted. 

 

 When grounding an external conductor (delta 

mains, two-phase mains), mains voltages (external 

conductor voltages) of up to 240VAC are 

permitted. 

 

Devices which are to be connected to an IT network must be provided with a 

separating transformer. Then the devices are operated locally as in a TN network. 

The secondary sided center of the separating transformer must be grounded and 

connected to the PE connector of the device. 

 

Summary of Contents for PSD1














































































































Reviews: