background image

5

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL                                       ALIGN™ MULTI-GAS GENERATOR

Do not install and operate this equipment until the safety information and instructions in this user guide have 

been read and understood by all personnel concerned.

USER RESPONSIBILITY:

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN 

OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE, AND VOID 

THE SAFTEY CERTIFICATION.

This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized dis

-

tributors provide product or system options for further investigation by users having technical expertise.

The user, through its own analysis and testing, is solely responsible for making the final selection of the 

system and components and assuring that all performance, endurance, maintenance, safety and warning 

requirements of the application are met. The user must analyze all aspects of the application, follow appli

-

cable industry standards, and follow the information concerning the product in the current product catalogue 

and in any other materials provided from Parker or its subsidiaries or authorized distributors.

To the extent that Parker or its subsidiaries or authorized distributors provide component or system options 

based upon data or specifications provided by the user, the user is responsible for determining that such 

data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of 

the components or systems.

Only competent personnel trained, qualified, and approved by Parker Hannifin should perform installation, 

start-up, service and repair procedures.

This equipment is for indoor use only. Do not operate outdoors.

Nitrogen is nontoxic and largely inert. It can act as a simple asphyxiant by displacing oxygen in air. Inhala-

tion of nitrogen in excessive concentrations can result in unconsciousness without any warning symptoms 

such as dizziness and fatigue.

The generator should be installed in an area with adequate ventilation to reduce the flammability of the oxy

-

gen-rich permeate stream. The system should not be installed in an area where the permeate stream poses 

the risk of explosion or combustion.

Use of the equipment in a manner not specified within this user guide may result in an unplanned release of 

pressure, which may cause serious personal injury or damage.

When handling, installing, or operating this equipment, personnel must employ safe engineering practices 

and observe all related regulations, health & safety procedures, and legal requirements for safety.

 

Never place liquids on top of the generator. 

Do not store anything on top of the generator. 

Never sit or climb on top of the generator.

Ensure casters are locked before starting up the generator.

Ensure that the equipment is depressurized and electrically isolated, prior to carrying out any of the sched

-

uled maintenance instructions specified within this user guide.

2. SAFETY INFORMATION

IOM_PKR_Align Multi-Gas Generator_022021.indd   5

IOM_PKR_Align Multi-Gas Generator_022021.indd   5

2/17/2021   1:11:40 PM

2/17/2021   1:11:40 PM

Summary of Contents for ALIGN-MG-JA


























Reviews: