Paragon Super User Instructions Download Page 6

6

5

5

ZONES

ZONES

Engineer Programmable Zones
Entry / Exit

This is a zone which allows limited-time access to the premises in
order to set or unset the system.

Access

This is a zone which, on setting the panel, allows access to the Entry /
Exit Zone. However, if the panel is set and an Access zone is
triggered before an Entry / Exit zone then an alarm will be generated
immediately.

Immediate

This is a  zone which will, when entered, go into alarm when the panel
is set.

Omitted

If a zone is programmed as an Omitted zone by the Engineer, then it
is ignored by the panel. Primarily used for Part set options. It also
allows the user to continue to use the alarm system even if a fault has
been discovered on one or more zones.

24 hour  zones
Personal Attack
Zone

Triggering of the Personal Attack zone will always cause a full alarm
activation regardless of whether or not the panel is set.

Tamper

A tamper zone activation will only generate an internal alarm, if the
panel is in Day mode. If a tamper fault is present and the panel is then
set, the system will give a second internal alarm. Triggering of a
tamper zone when the panel is set will always give an external as well
as internal alarm.

Fire

Triggering of the fire zone will only operate the internalsounder. A fire
alarm is identified by a three note rising sound which is easily
distinguished from all other tones.

6

6

CONTROLS AND FUNCTIONS

CONTROLS AND FUNCTIONS

Volume Control
This is only accessible when the front cover has been removed and will only affect the
volume of any extension speakers. The volume control is overridden when the panel
is in an alarm state, and should only be adjusted by the Engineer. The RKP has it's
own volume control.

A reduced volume tone can be obtained when setting the panel, by using the Easy-
Set functions.

The volume will be determined by the Engineer when setting up the system, by
adjusting the volume pot.

Chime
Chime function applies to ‘day’ mode only and if selected will cause the panel to
generate a three-note sound when an entry/exit zone is triggered. This feature is to
inform the occupants of the building that someone has entered.

RDOC 280 issue1

Zone

number(s)

QUICK REFERENCE GUIDES

QUICK REFERENCE GUIDES
LIMITED USER FUNCTIONS

LIMITED USER FUNCTIONS

1. Unsetting.

Enter

 

 (Limited User Code)

2. Full set.

Enter  

(Low Tone Volume)

or

 

(Max Tone Volume)

3. Part set.

Enter  

or 

(Low Tone Volume)

Enter  

or 

(Low Tone Volume)

Enter

(Low Tone Volume)

4. Clear flashing Alarm LED.

Enter 

(Limited User Code)

5. Zone omit on exit.

Enter 

 

 

6. Instant Fire Alarm.

 Enter

7. Instant Panic Alarm. Enter

8. Chime on/off.

Enter

9. Read Log.

Enter.

 To scroll forward:

.  To scroll back:

.

Symbols stored in the log and their meaning:

Entry/Exit zone activation.The panel was not unset before
the end of the entry time period, or User did not leave in time.

 to

Activation of a programmable zone.

This shows the next event in the log has triggered the alarm system

This shows that a zone was omitted and refers to the
number which precedes it in the log.

Tamper fault or sabotage.

Personal attack activation.

Fire alarm activation.

Leaving read-log function.

Enter

15

Summary of Contents for Super











Reviews: