Paragon Super User Instructions Download Page 10 | Manualshive

Page: 10 / 10

Paragon Super User Instructions Download Page 10

10

8

8

MASTER USER FACILITIES

MASTER USER FACILITIES

The Master User has access to all the Limited User facilities as well as those listed
below.

**The Paragon Super control panel has to be in ‘day’ mode after resetting with the
Master code for these additional features to be accessed.**

1) Resetting alarm LED after an Activation
To clear flashing Alarm LED

Enter

Master User (Factory set as 1234)

or

Limited User (Factory set as 5678)

2) Changing Limited User Code

Enter

then

Master User code - 2 Bleeps (Factory set as 1234)

then

New Limited user code - 2 Bleeps

then

New Limited user code again - 2 Bleeps

The ‘day’ led will flash when this function is entered and an acknowledge tone will be
sounded after each code has been entered. If an incorrect key is entered an error
tone will be given and the function ended.

3) Changing Master Code

Enter

then

Master User code, - 2 Bleeps (Factory set as 1234)

then

New Master User code, - 2 Bleeps

then

New Master User code. - 2 Bleeps

Errors tones as in 2) above.

4) System Test Mode

Enter
This function performs a number of tests which are listed below.
The next test is selected by pressing any numeric key.
To exit test mode press the Shift key again.

Test

1) All LED’s are switched on except the fault LED.
2) The strobe is switched on.
3) The bell is switched on
4) The internal sounder is switched on

1

1

RDOC280 issue1

5) Walk Test Mode

Enter
When the walk test mode is enabled the ‘chime’ LED will flash. If the panel is then full
set or part set each active zone will cause a chime when triggered. This enables all
the zone configurations to be walk tested individually. The walk test mode is cleared
when the panel is unset.

«
...
8
9
10

Summary of Contents for Super











Reviews:

No comments