background image

TIM1-A2-GZ40-00

September 2004

3

8. This Agreement and the license granted under this Agreement shall be 

terminated in the event of breach by the Licensee of any provisions of this 
Agreement. 

9. Upon such termination, the Licensee shall refrain from any further use of the 

Software and destroy the original and all copies of the Software in the 
possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without 

regard to its provisions concerning conflicts of laws.

Product Documentation Online

Complete documentation for Paradyne products is available at 

www.paradyne.com

. Select 

Support 

 Technical Manuals

.

To order a paper copy of a Paradyne document, or to speak with a sales 
representative, please call 1-727-530-2000. 

Release Notes

Release notes for this product are available in the subscriber firmware area of 

www.paradyne.com

. Select 

Support 

 Subscriber Firmware

.

Always review the relevant release notes before installing a new card.

 

Unpacking the TIM1500

HANDLING PRECAUTIONS FOR 
STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage 
due to electrostatic discharge (ESD) during normal operation. When 
performing installation procedures, however, take proper static control 
precautions to prevent damage to equipment. If you are not sure of the 
proper static control precautions, contact your nearest sales or service 
representative.

Unpack and inspect the TIM1500. If there is visible damage, do not attempt to 
connect the device; contact your sales or service representative.

!

Summary of Contents for TIM1500



















Reviews: