background image

 23

Document Feedback

We welcome your comments and suggestions about this document. Please mail them
to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,
or send e-mail to [email protected]. Include the number and title of this
document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.

Trademarks

All products and services mentioned herein are the trademarks, service marks,
registered trademarks or registered service marks of their respective owners.

Warranty, Sales, and Service Information

Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:

H

Via the Internet:

  Visit the Paradyne World Wide Web site at

http://www.paradyne.com

H

Via Telephone:

  Call our automated call system to receive current information via

fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Copyright 

E

 1998 Paradyne Corporation

Summary of Contents for Hotwire 5546
























Reviews: