Paradyne FrameSaver 9120 User Manual Download Page 46

Page: 46 / 82

Displaying System Information

4-20

9121-A2-GB20-20

May 1998

Field

What It Indicates

Status

Active Call Profile

8-Character ISDN Call
Profile identifier

ISDN Call Profile used for this
B-channel.

Appears when a call is active or in
progress.

Last Cause Value

Various ITU cause
messages

Maintenance and Troubleshooting.

Remote Call ID

None

Backup has never been active on
the B-channel.

Remote device’s ID

Remote call origination – Last
Calling ID of the remote device
received for the B-channel.

Local call origination – Called ID of
the remote device.

No Caller ID

The network is not providing the
caller ID of the calling device.

Negotiated Rate

64 Kbps
56 Kbps

Negotiated rate of the connection/
link.

Performance Statistics

Use the Status menu to display statistical information for a selected interface:

Network, Port-1, Port-2, DBM / BRI-B1, or DBM/BRI-B2. Statistical information is

useful when trying to determine the severity and frequency or duration of a
condition.

NOTE:

All statistics show the number of occurrences since the last reset of the
counter. In addition, only Level-1 and Level-2 Access Levels can view the
statistical information collected.

Summary of Contents for FrameSaver 9120


















































































Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands

Paradyne FrameSaver 9120, User Manual

Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands