Paradyne FrameSaver 9120 User Manual Download Page 25

Page: 25 / 82

Startup

3-3

9121-A2-GB20-20

May 1998

Procedure

Upon beginning a session, the Idle screen is displayed. To activate:

1. Press Return.

2. One of the following occurs:

I f . . .

Then . . .

What to do now?

Security is disabled

The Main Menu screen
appears.

Begin your session.

Security is enabled

You are prompted for a
login ID and password
(see

Logging In

page 3-1).

Enter your ID and
password. If Invalid
Password appears, see

Device Error Messages

Chapter 5,

Maintenance

and Troubleshooting.

Attempting to access the
unit through Telnet and the
user interface is currently
in session

The message Connection
refused: appears.
(FrameSaver access unit
allows only one
connection at a time.)

Maintenance and
Troubleshooting.

Attempting direct access
through the COM port and
the user interface is
currently in session

The message User
Interface Already In Use
appears with the active
user’s IP address.

Maintenance and
Troubleshooting.

Communication Port and
Login Required
configuration options are
enabled and there is no
contention for the user
interface

The Login screen
appears.

Enter your ID and
password. If Invalid
Password appears, see

Device Error Messages

Chapter 5,

Maintenance

and Troubleshooting.

Summary of Contents for FrameSaver 9120


















































































Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands

Paradyne FrameSaver 9120, User Manual

Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands