background image

4   Complete Installation Manual   

2.8

ZONE INPUTS

Detection devices such as motion detectors and door contacts are connected to the control panel's zone input terminals labelled Z1, Z2, Z3, Z4
and 

FIRE

 as shown in Figure 8-2: Zone Connections on page 14. Once the zones are connected, the associated zone's parameters must be

defined. For more information, please refer to 

Zone Programming 

on page 5. 

The 

FIRE

 input, which is recognized as zone 6, can be connected as a fire zone or a 24-hour burglary zone. Fire zones must use a 1k

 EOL

resistor. If a line short occurs or if the smoke detector becomes active, whether the system is armed or disarmed, the control panel will generate
an alarm on this zone.

2.9

KEYPAD INSTALLATION

Only the 1686V and the 1686H Spectra Keypads are compatible with the Spectra 1727 control panel. Remove the keypad’s back cover and wire
the 

GRN

YEL

RED

, and 

BLK

 terminals to the corresponding terminals on the control panel as shown in Figure 8-1: PCB Layout on page 13.

2.10

KEYPAD ZONE INSTALLATION

The keypad has one zone input terminal that allows you to connect one motion detector or one door contact directly to the keypad. The keypad
zone is recognized as zone 5. Only one keypad zone can be used per Spectra 1727 control panel. The keypad communicates the status of the
keypad zone to the control panel once the device is connected as shown in Figure 8-1: PCB Layout on page 13 and the zone’s parameters are
defined (see section 3.2). For example, a door contact located at the front door can be wired directly to the input terminal of the keypad instead of
wiring it back to the control panel.

2.11

KEYPAD TAMPER

If the keypad has a tamper switch, the state of the tamper is displayed on zone 5. The control panel cannot differentiate between the open
keypad zone and an open keypad tamper.

Table 1: PGM Events

PGM Event

Description

Exit Delay

The PGM activates during the Exit Delay.

Armed

The PGM activates while the system is armed.

Ready

The PGM activates while the 

READY

 LED is illuminated.

“PG” Key

The PGM activates when the 

PG

 key is pressed and deactivates when the key is pressed again.

Fire Alarm

The PGM activates during a Fire Alarm.

Audible Alarm

The PGM activates during any alarm.

Strobe

The PGM activates while the 

ARM

 LED flashes in alarm.

Entry Delay/Exit Delay/Alarm

The PGM activates during the Entry Delay, the Exit Delay and during an alarm.

Exit Delay/Armed

The PGM activates during the Exit Delay or while the system is armed.

Entry Delay/Alarm

The PGM activates during the Entry Delay or during an alarm.

Regular Armed

The PGM activates while the system is Regular Armed.

Table 2: PGM Options

Option

PGM 1 Events
First Digit

PGM 2 Events
Second Digit

[0]

Exit Delay

Exit Delay

[1]

Armed

Armed

[2]

Ready

Ready

[3]

“PG” Key

“PG” Key

[4]

Fire Alarm

Fire Alarm

[5]

Alarm

Alarm

[6]

Strobe

Strobe

[7]

Entry Delay/Exit Delay/Alarm

Entry Delay/Exit Delay/Alarm

[8]

Exit Delay/Armed

Entry Delay/Alarm

[9]

Regular Arming

Entry Delay/Alarm

Summary of Contents for SPECTRA 1727





















Reviews: