background image

To reprogram the timer, press 

[

ENTER

]

, followed by the master

code/user code 1, and 

[

MEM

]

. Key 

[

MEM

]

flashes. Then enter 2

digits (00 to 23) for hours, followed by 2 digits (00 to 59) for min-
utes. Press 

[

ENTER

]

.

Trouble 9

Tamper/zone wiring failure

Indicates that there is a wiring problem in a protected zone, the
LCD display reads “

TROUBLE

09 

TAMPER

”.

Trouble 10

Telephone line monitor

If the panel detects telephone line loss, the LCD display reads

TROUBLE

10 

PHONE LINE

”.

Trouble 11

Fire/trouble

If the fire zone is cut, fire zone key and trouble, the display will
read“ 

TROUBLE

11 

FIRE LOOP

”.

Most  "trouble" conditions will be programmed by your installer to
be reported directly to your security company. Please contact
your alarm company to ensure that repairs are immediately made
to your security system.

Fire Alarm Operation

Alarm

Upon a Fire Alarm, the bell/siren will operate in "pulse mode".

Silence/Reset

:

To silence/reset a fire alarm, enter a valid user code. 

IMPORTANT: IN CASE OF FIRE, FOLLOW YOUR EVACUATION
PLAN IMMEDIATELY! 

If there is no fire condition, contact your mon-

itoring company without delay to avoid an unnecessary response.

UM639

23

power supply is unable to charge the battery 

and/or 

the power

supply voltage exceeds 14.9 volts, the LCD display will read

TROUBLE

02 

POWER SUPPLY

”. Power failure can be excluded from

[

TRBL

key display by your alarm installer.

Trouble 4 

Bell disconnect

If a bell or siren is not connected to the bell/siren output, “

TROU

-

BLE

04 

NO BELL

” appears in the display.

Trouble 5

Maximum bell current

If the processor recognizes that the bell/siren output current
exceeds 3A,. the LCD display reads “

TROUBLE

05 

MAX BELL OUTPUT

”.

Automatic bell output shutdown results. Once the problem is cor-
rected, power will automatically be restored to the bell/siren circuit.

Trouble 6

Maximum auxiliary current

If the processor has recognized that the auxiliary output current
exceeds 

1A

(748ES - 

3A

), the LCD display will read “

TROUBLE

06

MAX AUX OUTPUT

”. This causes automatic shutdown of the auxiliary

output. Once the problem is corrected, power will automatically
be restored to the auxiliary output. This output powers such
devices as motion detectors and accessory modules. 

Trouble 7

Communicator report failure

If your control panel cannot communicate with the central moni-
toring station, the LCD display reads “

TROUBLE

07 

COMMUNICATION

”.

Trouble 8

Timer loss

If the system timer is not functioning, usually after a total battery
and AC power failure, the LCD display reads “

TROUBLE

08 

TIMER

LOSS

”. The timer should be reprogrammed after total power loss. 

UM639

22

Summary of Contents for Esprit 639


















Reviews: