ParaBody 425104 Assembly Instructions Manual Download | Manualshive

Page: 44 / 46

background image

• If upon completion of assembly, the HEAD PLATE (72) does not

sit on top of the first WEIGHT PLATE (105), push the HEAD
PLATE (72) down, insert the WEIGHT STACK PIN (75) and
perform several repetitions at the press station. This will relax the
cable system and prevent the HEAD PLATE (72) from lifting up.

STEP 52

• If after completing previous step, the HEAD PLATE (72) still does

not sit on top of the first WEIGHT PLATE (105) or if there is
excess slack in the cable system, adjust the two threaded ends of
the HEAD PLATE CABLE (102) accordingly and retighten the jam
nuts.

• If there is excess slack in the AB or PEC DEC cable system, adjust

the threaded end of the AB CABLE (103) accordingly and re-
tighten the jam nut.

44

72

75

105

102

FIGURE 52

STEP 53

•

Apply pressure to the bottom of one SHROUD (31) where thw “V” groove is and carefuly remove the weight stack opening on the plastic

SHROUD (31) as shown in FIGURE 53. This will be the front SHROUD (31).

FIGURE 53

•

Apply one PARABODY 425

SERIOUS STEEL

LABEL (32) to the front SHROUD (31) approximately 6-1/2” from the top as shown in FIGURE

53.

32

31

31

6-1/2”

«
...
42
43
44
45
46
»

Summary of Contents for 425104















































Reviews:

No comments

Related manuals for 425104

Bodylift 831.159412

Brand: Pro-Form Pages: 17

Brand: Life Fitness Pages: 15

Brand: Paramount Fitness Pages: 24

2.0AS Assembly and

Brand: AFG Pages: 15

Brand: Bowflex Revolution Pages: 25

Brand: SPORTSTECH Pages: 212

Brand: ParaBody Pages: 6

Magnetic Rower NS-RE6000

Brand: Abilica Pages: 34

CLASSIC MCB-5702

Brand: Marcy Pages: 13

Brand: Weider Pages: 7

Brand: Weider Pages: 7

Brand: Weider Pages: 16

Brand: Sunny Pages: 10

Brand: Asaklitt Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands