ParaBody 425104 Assembly Instructions Manual Download | Manualshive

Page: 13 / 46

background image

13

FIGURE 13

STEP 13

• Insert two GUIDE RODS (36) into the BASE (1) as shown on FIGURE 13.

(NOTE: Lubricate GUIDE RODS (36) with silicon or teflon

spray available at most hardware stores.)

• Slide two 1-1/4 SQ. X 4-7/8” TUBES (34), two 3/4” WASHERS (71), and two WEIGHT STACK CUSHIONS (70) -

IN THAT

ORDER -

down over the GUIDE RODS (36).

•

SECURELY

assemble the SELECTOR SHAFT (73) to the HEAD PLATE (72) using one 3/8 X 1-1/4” BOLT (83) and one 3/8”

WASHER (91).

• Using

EXTREME CARE

slide all fifteen WEIGHT PLATES (105) down over the GUIDE RODS (36) on to the WEIGHT STACK

CUSHIONS (70). Make sure that the keyholes of the WEIGHT PLATES (105) are all facing the right way.

(NOTE: If the359101 50

LB. ADD-KIT is purchased refer to the 359101 ASSEMBLY INSTRUCTIONS now.)

• Insert four CAP PLUGS (55) into the top and bottom ends of the GUIDE RODS (36) as shown in FIGURE 13.

• Slide the head plate assembly down over the GUIDE RODS (36) onto the weight stack.

• Attach the WEIGHT STACK LABELS (104) to the weight stack. Also insert the WEIGHT STACK PIN (75) into the first

WEIGHT PLATE (105) of the weight stack.

55

36

105

1

73

91

75

104

70

71

34

83 3/8 X 1-1/4”

72

55

«
...
11
12
13
14
15
...
»

Summary of Contents for 425104















































Reviews:

No comments

Related manuals for 425104

Brand: Zen Pro Pages: 44

Platinum PRO 17PTRW2000

Brand: Tunturi Pages: 84

Brand: Master Pages: 78

Brand: Master Pages: 90

Brand: LifeGear Pages: 45

Brand: Iron Gym Pages: 2

Brand: SPORTSTECH Pages: 212

Brand: Impex Pages: 11

NordicTrack NTBE17917.0

Brand: ICON Health & Fitness Pages: 16

Brand: Kayoba Pages: 40

Marcy Platinum MP-PWR10.0

Brand: Impex Pages: 21

Brand: Body Solid Pages: 9

Brand: Pro-Form Pages: 12

Brand: TuffStuff Pages: 20

CLASSIC MCB-5702

Brand: Marcy Pages: 13

Brand: WIEDER Pages: 8

NEMO III SF-2380

Brand: Skandika Pages: 56

REGATTA OXFORD PRO PLUS

Brand: Skandika Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands