35
34
USER MANUAL
PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM
Level 4 – Resetting to factory settings.
The procedure recovers the factory settings of the system without deleting previously registered de-
vices (tags, mobile device, relays, etc.) that is stored in the non-volatile memory.
To reset the settings enter the programming mode and press VALET button four times. Press and hold
VALET button for more than 4 seconds until siren sound, then release the button. The system will con-
firm the resetting to the factory settings with a long red flash of LED indicator. After that the system will
return to a programming mode
Level 5 – Recording Bluetooth engine compartment module
To record a Bluetooth engine compartment module, enter programming mode and press VALET button
5 times. The LED indicator will light green and the system will enter the recording of an engine com-
partment module mode. Connect the module in accordance with installation manual. The system will
confirm the registration with a short sound signal.
Saving changes:
To finish the recording of the engine compartment module, VALET button should be pressed once
again, the series of red and green flashes of the status LED will confirm the saving, switch on the ignition
to automatically save the settings and exit programming mode.
Levels 6, 7 – Recording Bluetooth radio relays
Radio relays recording is performed one by one starting from the 6 level: radio relay №1 is
recorded on the 6 level; radio relay №2 is recorded on the 7 level. The radio relay can be overwrit-
ten only on the level of its initial registration.
To record Bluetooth radio relays №1, №2, enter programming mode and press VALET button 6 times
for radio relay №1 or 7 times for radio relay №2. LED indicator will light green and the system will enter
the recording of a radio relay mode. Connect a relay in accordance with installation manual. The system
will confirm recording with a short sound signal.
Saving changes:
To finish the recording of the Bluetooth radio relay, VALET button should be pressed once again, the
series of red and green flashes of the status LED indicator will confirm the saving, switch on the ignition
to automatically save the settings and exit the programming mode.
Level 8 – Recording Bluetooth GPS/GLONASS receiver (NAV-035 BT)
To record a Bluetooth GPS/GLONASS receiver, enter programming mode and press VALET button 8
times. The LED indicator will light green and the system will enter the recording of a receiver. Connect
the receiver in accordance with its installation manual. The system will confirm the registration with a
short sound signal and red light of LED indicator.
Saving changes:
To finish the recording of the engine compartment module, press VALET button once, the series of
red and green flashes of the status LED will confirm the saving, switch on the ignition to save the set-
tings and exit programming mode.
Level 10 – Configuring system settings via the wireless interface
This function is under construction.
Level 11 – Programming and configuring ‘Immobilizer PIN code’
To program the
«Immobilizer PIN code»
, enter the programming mode and press VALET button 11
times. The level is divided into 3 sublevels
(Sublevel 11.1 – Selecting buttons; sublevel 11.2 entering
PIN-code; sublevel 11.3 – confirmation of the PIN-code input
).
The system will automatically enter the sublevel 11.1 (Selecting buttons) after entering the level 11.
The system can determine buttons via analog “
Code immobilizer
” input or via digital protocol of a car.
It is necessary to configure an analog input (INP) as ‘
Code immobilizer
’ in the settings of the base
unit inputs when implementing the “
Code immobilizer
” via an analog input. It may be necessary to
switch on the ignition after entering the level 11 of programming (if the car bus is active only when
the ignition is switched on) when implementing the “
Code immobilizer
” via digital car bus protocol.
After selecting active buttons enter the sublevel 11.2 (
Entering PIN-code
) by pressing VALET but-
ton once. Program PIN-code using selected buttons at this sublevel; press
VALET
button once and enter
PIN-code again. To confirm PIN-code re-entering and save all the settings press
VALET
button once
again.
Sublevel 11.1 - Selecting buttons:
This sublevel is used to select active buttons via digital protocol of a car or via
‘Code Immobilizer’
analog input. To determine the activity of the analog
“Code Immobilizer”
input, apply potential to the
corresponding input (INP) of the base unit, LED indicator will be flashing orange.
If you determine buttons via digital protocol select one or more buttons (up to four) for entering
the secret code of the immobilizer. To do this press the selected button, LED indicator will confirm input
