33
32
USER MANUAL
PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM
Level 16
Updating Bluetooth modem firmware
Level 17
Programming bypass of original immobilizer
Level 18
Pairing and unpairing mobile device
Level 19, 20
Updating radio relays №1, №2 firmware (BTR-101)
Level 21
Updating Bluetooth engine compartment module firmware (RHM-03 BT)
Level 22
Updating Bluetooth GPS/GLONASS receiver firmware (NAV-035 BT)
Level 23, 24
Recording door sensors №1, №2 (DMS-100 BT)
Level 25, 26
Updating door sensors №1, №2 firmware (DMS-100 BT)
Enter programming mode by entering the ‘Service PIN-code’, Use
VALET
button to enter the desired
level number (press the button a number of times, equal to level number; pauses between presses
should not exceed 1 second). The system will confirm correct input with red LED flashes and short
sound signals of a siren and proceed to the desired level. If the input was incorrect, the system will not
confirm input and will await a new level input after a series of green and red flashes
Level 1 – Recording radio tags into the system’s memory
Prepare to record all radio tags
(you can record up to 3 tags), install batteries in the radio tags.
Enter programming menu and then press VALET button once. LED indicator will light green and
the system will enter the tag recording mode. Tags are recorded (paired) one by one, in any order and
without time limit. All previously registered radio tags will be removed when you overwrite new tags
or overwrite old tags.
Recording radio tags:
Press control button on a tag and hold it for 6 seconds (6 flashes of tag status indicator), release the
button after the sixth flash. If the recording was successful, a siren will emit 1 beep, after that you can
move to recording the next tag
Saving changes:
To finish the recording of radio tags into the system,
VALET
button should be pressed once again,
the series of red and green flashes of status LED indicator will confirm the saving.
Level 2 – Changing the factory preset of the service PIN-code
Prepare a new value of the ‘Service PIN-code’, it should consist of 4 digits (from 1 to 9).
Write down or remember the new PIN-code.
Enter programming menu and then press VALET button twice. The system will enter ‘Changing Ser-
vice PIN-code’ mode and the status LED indicator will turn off.
Changing the ‘Service PIN-code’:
• Enter the first digit of the code using VALET button. Press the button a number of times, equals
to the first digit. Pauses between presses should not exceed 1 second, every pressing will confirm with
orange LED indicator flash. Pause for more than 1 second and red LED indicator confirms the input of
the first digit. Then you can enter the next digit.
• Enter the other numbers in the same manner. The input of the fourth number will be confirmed
by series of red and green LED indicator flashes. The system will wait for PIN-code re-entering.
• Enter all four digits again;
• If you were able to correctly enter the ‘Service PIN-code’ twice, the indicator will produce the series
of red and green flashes, new PIN-code will be recorded, the system will return to programming mode.
In case of the incorrect code input the indicator will be lit red, the system will return to programming
mode.
Level 3 – Recording the idle speed to the system memory
To timely turn off the starter during automatic or remote engine start via digital or analog tachometer
input and the correct operation of the ‘Smart Turbo Timer’, it is necessary to record the engine idle speed
To record idle speed to the non-volatile system memory, enter the programming menu. Press VALET
button three times. Switch on the ignition and start the engine after entering this level of programming
(the engine should be warmed-up, idle speed should match the stable idle speed of the warmed-up en-
gine). The system will confirm the presence of the idle speed status with green flashes of LED indicator.
Wait until the stable idle speed will be reached and save the changes
Saving changes:
Press VALET button once to save idle speed. Successful recording of the idle speed will be confirmed
with the series of red and green flashes of LED indicator. The system will exit programming menu and
reboot after saving the idle speed.
