11
10
USER MANUAL
PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM
Control over the system in case of emergency
Use a phone to deactivate the system quickly. To disarm the system via a phone, call the system’s
number. When it answers, dial command
0*.
If the call is not made from the owner’s number, guest PIN-
code should be entered. Factory set guest PIN-code is
1-2-3-4.
To switch off an immobilizer tag, dial the
998*
command (after dialing, enter the ‘Secret PIN-code’
that is located on the owner’s plastic card). To switch on an immobilizer tag, dial the
888*
command. If
the system cannot be deactivated via a phone, apply emergency disarming and switching on/off an
immobilizer tag using VALET button.
Emergency disarming using «VALET» button
In case you cannot disarm the system using a phone or immobilizer tag, the ‘Secret PIN-code’ can
be used. The ‘Secret PIN-code’ is written on the owner’s plastic card under protective layer. Erase the
protective layer and use
VALET
button to input the PIN-code.
The code must be entered only when the base unit is powered and the ignition is switched off. The
PIN-code can be entered using external or located on the base unit
VALET
button. The digits input and
correct input is indicated by the external or located on the base unit
LED
indicator.
Entering the PIN-code
• Enter the first digit of the code using VALET button. Press the button a number of times, equals to
the first digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with
an orange LED indicator flash. A Pause for more than 1 second and a red LED indicator flash confirm the
input of the first digit. Then you can enter the next digit.
• Enter the second digit of the code using
VALET
button. Press the button a number of times, equals to
the second digit. Pauses between presses should not
exceed 1 second. Each pressing will be confirmed with
an orange
LED
indicator flash. A Pause for more than 1
second and a red
LED
indicator flash confirm the input
of the second digit. Then you can enter the next digit.
• Enter the third digit of the code using
VALET
but-
ton. Press the button a number of times, equals to the
third digit. Pauses between presses should not exceed 1
second. Each pressing will be confirmed with an orange
LED
indicator flash. A Pause for more than 1 second and
a red
LED
indicator flash confirm the input of the third
digit. Then you can enter the next digit.
• Enter the fourth digit of the code using
VALET
but-
ton. Press the button a number of times, equals to the
fourth digit. Pauses between presses should not exceed
1 second. Each pressing will be confirmed with an or-
ange
LED
indicator flash.
The system will confirm correct PIN-code with the
series of red and green flashes and the system will be
disarmed. If the input was incorrect, it will be indicated
with a red
LED
indicator flash and the system will stay in a previous state. New input can be attempted
after 5 seconds.
If the system was disarmed and the ignition was switched off it will enter programming mode after
correct input of the PIN-code.
For emergency arming when the ignition is switched off, press and hold
VALET
button for 3 sec-
onds. The system will be armed in 30 seconds. Status LED indicator is lighting red during the countdown.
2-2-2-2
PIN
Three-color status
LED
indicator (green, red,
orange)
VALET
button
VALET BUTTON
WARNING! MAKE SURE THAT A PROTECTIVE LAYER ON THE OWNER’S PLASTIC
CARD IS INTACT AFTER THE INSTALLATION OF THE SYSTEM. THE PLASTIC CARD
HOLDS THE ‘SECRET PIN-CODE’.
WARNING! CAREFULLY REMOVE THE PROTECTIVE LAYER, DO NOT USE SHARP
OBJECTS TO AVOID DAMAGING OF HIDDEN INFORMATION UNDER A PROTEC-
TIVE LAYER.
