background image

13

12

User manual

Pandora DXL-0100L/0101L service-security system

entering of the first digit with red LED indicator flash.

WARNING! 

IF YOU ARE AN INSTALLER, DO NOT ERASE PROTECTIVE LAYER OF THE OWNER’S 

PLASTIC CARD! IN CASE A CUSTOMER COMPLAINS ON ERASED PROTECTIVE LAYER 

OF THE CARD WITH THE INDIVIDUAL PIN-CODE, RE-INSTALLATION OF THE SYSTEM 

IS CARRIED OUT AT THE EXPENSE OF THE INSTALLER.

5. Similarly input the second, third and fourth digit. Every input will be confirmed with red LED 

flash.

6. The system will confirm correct PIN-code with red LED flashes and proceed to the programming 

mode. If the input was incorrect, it will be indicated with long red flash and the system will proceed to 

previous mode. New input can be attempted after 5 seconds.

Changing core settings via computer

The system allows programming all settings and updating software of the base unit via the 

interface micro-USB cable or via radio channel using a computer. It does not matter, whether base 

unit is installed into a vehicle or not. Software reads the current settings and allows changing them. 

If base unit has not yet been installed in the vehicle, it should be powered via micro-USB cable while 

programming. To program using a computer connected via cable, you need a standard micro-USB 

cable, a computer with Windows and a special piece of software – Pandora AlarmStudio.

In preparation to the programming following stages should be followed:

• connect micro-USB cable to any free USB socket of the computer;

• start Pandora AlarmStudio (can be downloaded from the web-site);

• enter the programming settings mode by entering the service PIN-code on the base unit using 

VALET button. Factory preset PIN-code is 1-1-1-1.

If the software configuration is carried out via the radio interface of 2,4 GHz, special USB programmer 

RMP-03 should be used.

Wire 11 (Orange-black) (‘CAN1-Low’) It connects to appropriate CAN-Low wire of the car.

Wire 12 (Yellow-black) (‘CAN2-Low’/OUT-5) Factory setting is ‘Close central lock’. A negative 

impulse of 0,8 seconds is formed on the wire to close central lock. Logic of the channel’s operation 

can be set in the table of system outputs in AlarmStudio. When the channel is cleared from assigned 

operating algorithms, it starts operating as CAN2-Low and the wire connects to appropriate CAN-Low 

car wire.

Wire 13 (Blue-black) (OUT-3) Factory setting is ‘Blocking’. This wire is used to control external 

analogue blocking relay with a normally open logic (it becomes grounded when switching on the 

ignition and security system is not armed and radio tags are in range).

Wire 14 (Yellow) (INP-2) Factory setting is ‘Ignition’. This wire connects to ignition switch or to 

appropriate wire where 12V voltage appears when ignition is switched on and doesn’t disappear until 

the moment ignition is switched off. This input is multipurpose, it can operate in accordance with 

selected logic.

Wire 15 (Purple) (‘siren’) It connects to siren control wire (+) (maximum load current is 2A).

Wire 16 (Red) (‘Power supply’ 12V) It should be connected to reliable conductor with constant 

voltage of 12V.

Programming system and entering PIN-code

The system settings can be changed via computer. The system should be connected to a computer 

via standard micro-USB cable and a special piece of software – Pandora AlarmStudio.

AlarmStudio can be downloaded from the official company web-site pandorainfo.com

Entering programming menu:

1. Disarm the system, switch off the ignition.

2. Connect the base unit of the system to a computer via micro-USB cable.

3. Using VALET button, input service PIN-code. Factory preset PIN-code is 1-1-1-1.

4. Using VALET button, input the first digit of the service code (press the button a number of times, 

equal to the first digit; pauses between presses should not exceed 1 second). The system will confirm 

Summary of Contents for DXL-0100L


















Reviews: