33
32
USER MANUAL
SECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
Automatic modes
There are automatic lock modes that will lock the doors at the car movement or on switching on the
ignition. When using doors locking mode on car movement start, the system will detect car moving
and perform doors locking (it depends on speed status in a digital CAN-bus or motion sensor sensitivity
settings). When using doors locking mode on switching on the ignition, the doors will be locked
automatically 5 seconds after the ignition was switched on. If any door was opened after the ignition
had been switched on, automatic locking will be disabled to prevent locking the keys inside the car.
Doors can be automatically unlocked when the ignition is switched off.
!
T
hese
modes
are
disabled
by
defaulT
,
use
The
p
andora
a
larm
s
Tudio
To
enable
These
seTTings
.
Car search function
To easily find your vehicle on a massive parking, shortly press the
button when the car is armed. The
system will sound the siren
and flash turn signals
5 times in a row. To use this function without
sound signals press and hold the
button for 1 second.
PANIC mode
If your car or you are in danger and you want to draw attention to your car, you can use PANIC mode. In
this mode the siren will sound and turn signals will flash repeatedly for 30 seconds.
To activate this mode, use one of the methods described below.
Remote control
To activate the PANIC mode, press the
and
buttons simultaneously. To switch it off, press either
or
button.
Mobile application
Open the mobile application. When the system is online (there is an Internet or Bluetooth connection),
press and hold the
button on the control panel until the scale is fully loaded. To switch this function
off press and hold the
button on the control panel until the scale is fully loaded.
Service mode
It is recommended to put the system into the service mode before handing it to a car service or valet
parking. When this mode is switched on, security system stops interfering with built-in electronics and
disables all functions to ease maintenance.
To switch on this mode, disarm the system, turn on the ignition, an authorization device (a radio
tag, a remote control, a mobile phone) must be in the coverage zone, enter the “Immobilizer PIN-
code” (if the “Code immobilizer” function is used) and use one of the method described below:
Radio tag
To activate/deactivate service mode, press and hold the
button on a radio tag for 3 seconds
(until the third flash of the LED), release the button.
Phone
Call the system number wait for the answer.
• To activate service mode, dial the
1
5
5
*
DTMF command and then dial the “Secret PIN-code”
from the Owner’s personal card.
• To deactivate service mode dial the
2
5
5
*
DTMF command.
•
Mobile application
To activate/deactivate service mode, open the mobile application. When the system is online (there
is an Internet or Bluetooth connection), press and hold the
button on the control panel until
the scale is fully loaded.
!
T
o
change
buTTons
layouT
or
add
new
buTTons
on
The
conTrol
panel
,
go
To
“s
eTTings
c
onTrol
buTTons
“.
Immobilizer buttons
• To activate service mode, enter the “Immobilizer PIN-code” and press the immobilizer button 10
times within 20 seconds.
• To deactivate service mode, turn on the ignition and enter the “Immobilizer PIN-code”.
Service mode indication
• Activated Service mode is indicated by: an icon
in the mobile application, constant green LED
when the ignition is on, long sound signal of a Beeper at the moment you activate the mode.
• Deactivated Service mode is indicated by: no “Service mode” icon
in the mobile application in
the mobile application, no constant green LED when the ignition is on, two long sound signal of a
Beeper at the moment you deactivate the mode.